Where provided thresholds shall be 2 inches (51 mm) maximum in height and have a beveled or sloped angle not exceeding 1 unit vertical in 2 units horizontal (26.6 degrees from the horizontal...
Search Results "Maximum Dimension"
-
11B-809.10.6.5 Thresholds
-
11B-812.5.4 Arrangement
Vehicle spaces installed in existing facilities shall comply with Section 11B-812.5.4 to the maximum extent feasible....
-
11B-809.10.6.4 Reinforcement for grab bars
Reinforcement for grabs bars shall comply with the following: Continuous reinforcement shall be installed in the walls of showers 30 inches (762 mm) maximum to 38 inches (965 mm) minimum...
-
607.4.2.1 Back Wall
Two grab bars shall be installed on the back wall, one located in accordance with 609.4 and other located 8 inches (205 mm) minimum and 10 inches (255 mm) maximum above the rim of the bathtub...
-
Protrusions
Objects may protrude into the space a maximum of 6 inches along the front of the space, if they are between 9 inches and 27 inches maximum above the floor....
-
608.7 Thresholds
Thresholds in roll-in type shower compartments shall be 1/2 inch (13 mm) high maximum in accordance with 303....
-
11B-607.4.2.1 Back wall
Two grab bars shall be installed on the back wall, one located in accordance with Section 11B-609.4 and the other located 8 inches (203 mm) minimum and 10 inches (254 mm) maximum above the...
-
Stanley Hardware 8179 Light Commercial Door Closer
Product Overview Used on doors with a maximum weight of 185lbs and is UL listed Adjustable closing and latching speed Reversible for left or right swing Includes tri-pack hardware...
-
The ADA Standards for Accessible Design (the ADA Standards)
The ADA Standards identify what features need to be accessible, set forth the number of those features that need to be made accessible, and then provide the specific measurements, dimensions...
-
Sections 4.8.5 and 4.9.4
An exception permits the distance between the horizontal projections and the bottom of the gripping surface to be reduced by 1/8 inch for each ½ inch of additional handrail perimeter dimension...
-
Water Closet Centerline and Seat Height
Water closets can be located so that this dimension is met on either the left side or the right side of the fixture....
-
13. Do the provisions for openings in floor and ground surfaces in Section 302.3 apply to walking surfaces in play areas?
If gratings or openings have elongated openings, they must be placed so the long dimension is perpendicular to the dominant direction of travel....
-
COST OF EQUIPMENT
COST OF EQUIPMENT Table 1: Cost of Equipment Configurations Dimensions Price Range Average Price Price Increase Configuration #1:...
-
Supporting Documents for the Medical Diagnostic Equipment Accessibility Standards Advisory Committee Report
Subcommittee Report - Imaging Equipment Subcommittee Report - Mammography Subcommittee Report - Stretchers Subcommittee Report - Weight Scales IDeA Center Memo – Transfer Surface Dimensions...
-
Is a transportation operator required to procure vehicles with lifts that have a design load of more than 600 pounds?
However, if a transportation operator procures vehicles with lifts that have a design load of more than 600 pounds, or the platform and vehicle will accommodate a wheelchair that exceeds the dimension...
-
Is a transportation operator required to procure vehicles with lifts that have a design load of more than 600 pounds?
However, if a transportation operator procures vehicles with lifts that have a design load of more than 600 pounds, or the platform and vehicle will accommodate a wheelchair that exceeds the dimension...
-
Doorways [4.8.4]
Keeping the door swing clear of minimum landing dimensions is a good idea, especially at the bottom of ramps since people using wheelchairs may exit them with some force and speed....
-
4.10.4 HALL LANTERNS
(2) Visual elements shall be at least 2-1/2 in (64 mm) in the smallest dimension. (3) Signals shall be visible from the vicinity of the hall call button....
-
11B-404.2.7 Door and gate hardware
Operable parts of such hardware shall be 34 inches (864 mm) minimum and 44 inches (1118 mm) maximum above the finish floor or ground....
-
11B-404.2.7 Door and gate hardware
Operable parts of such hardware shall be 34 inches (864 mm) minimum and 44 inches (1118 mm) maximum above the finish floor or ground....
-
Grab bars
The outside diameter dimension range for circular cross-section grab bars are between 1.25 and 2 inches. A 1.5 inch diameter was chosen for the study....
-
A4.32.4 Height of Tables or Counters
34 865 Seated in a 16 in (405 mm) high chair: Manual work 26 660 27 685 Light, detailed work 28 710 31 785 1All dimensions...
-
A4.32.4 HEIGHT OF WORK SURFACES
Seated in a 16-in (405-mm)-high chair: Manual work 26 660 27 685 Light, detailed work 28 710 31 785 * All dimensions...
-
604.7 Dispensers
Toilet paper dispensers shall comply with 309.4 and shall be 7 inches (180 mm) minimum and 9 inches (230 mm) maximum in front of the water closet measured to the centerline of the dispenser...
