The nursing bench 3000 series provides for maximum safety and comfort....
Search Results "Maximum Dimension"
-
Pressalit Care Nursing bench 2000, electrically height adjustable
-
Ambulatory Accessible Compartment
Throughout the new guidelines, the Board has sought to specify dimensions as a range instead of in absolute terms where practicable to facilitate compliance without compromising accessibility...
-
5.3.2.1 Transfer Sides Recommendation for Stretchers
5.3.2.1 Transfer Sides Recommendation for Stretchers On stretchers, the transfer surface is oriented along the long dimension of the surface on which patients are in the supine, prone...
-
9. Exterior Ramps
[ADA Stds. 4.8.3] Yes __ No __ N/A __ Comments: _______________________________ d. do the exterior ramps have running slopes that are 1:12 or less (critical dimension of 2" or less...
-
11B-405.7.5 Doorways
Doors, in any position, shall not reduce the minimum dimension of the ramp landing to less than 42 inches (1067 mm). [2010 ADAS] 405.7.5 Doorways. ...
-
Platform Edges
This depth is an absolute dimension, not a minimum. Some platforms are edged with a buffer material that is designed to break away if hit by cargo trains....
-
Space Allowance and Reach Ranges [4.2]
Adult dimensions and measures for standard manual wheelchairs form the basis of many ADAAG specifications....
-
505.6 Gripping Surface
distance between horizontal projections and the bottom of the gripping surface shall be permitted to be reduced by 1/8 inch (3.2 mm) for each 1/2 inch (13 mm) of additional handrail perimeter dimension...
-
4.4.4 Clear Floor or Ground Space
The long dimension of the clear space shall be roughly perpendicular to the length of the bench....
-
Department of Justice method
Use the tape measure and measure the open gap at the downhill end of the level to establish the critical dimension....
-
11B-405.7.5 Doorways
Doors, in any position, shall not reduce the minimum dimension of the ramp landing to less than 42 inches (1067 mm). [2010 ADAS] 405.7.5 Doorways....
-
11B-703.7.2.1 International Symbol of Accessibility
A border may be provided inside or outside of the minimum required International Symbol of Accessibility dimension....
-
11B-603.4 Coat hooks, shelves and medicine cabinets
Shelves shall be located 40 inches (1016 mm) minimum and 48 inches (1219 mm) maximum above the finish floor....
-
Stanley SB600 Bifolding Door
safety sensors and advanced activation sensors Door panels fold in or out for the most efficient use of space at entrances or exits HEIGHT: 2 Panel: 7’-6” (2.2m) Minimum, 9’-2” (2.8m) Maximum...
-
904.3.2 Counter
The counter surface height shall be 38 inches (965 mm) maximum above the finish floor or ground....
-
Ramps
For each elevated ramp run: 12-inch (305 mm) maximum rise 1:12 maximum slope 36-inch (915 mm) minimum clear width ...
-
4. Comparison of Proposed Technical Provisions Applicable to Shared Use Paths and AASHTO Guide
Vertical surface discontinuities shall be 13 mm (0.5 in) maximum....
-
Passing Spaces: ADA Standard Section 403.5.3
Section 403.5.3 covers the current ADA Standards for passing spaces that are part of an accessible route.
-
1607A.9.2 Grab bars, shower seats and accessible benches
designed to resist a single concentrated load of 250 pounds (1.11 kN) applied in any direction at any point on the grab bar, shower seat, or seat of the accessible bench so as to produce the maximum...
-
11B-809.10.7.2 Location
The centerline of the water closet shall be 17 inches (432 mm) minimum to 18 inches (457 mm) maximum from a wall or partition that is 54 inches (1372 mm) minimum in length....
-
11B-809.10.7.2 Location
The centerline of the water closet shall be 17 inches (432 mm) minimum to 18 inches (457 mm) maximum from a wall or partition that is 54 inches (1372 mm) minimum in length....
-
11B-904.3.2 Counter
The counter surface height shall be 38 inches (965 mm) maximum above the finish floor or ground....
-
T302.4 Surface Discontinuities
Surface discontinuities shall be ½ inch (13 mm) high maximum and shall be beveled with a slope not steeper than 1:2. EXCEPTIONS: 1....
-
705.1.1 Dome Size
Truncated domes in a detectable warning surface shall have a base diameter of 0.9 inch (23 mm) minimum and 1.4 inches (36 mm) maximum, a top diameter of 50 percent of the base diameter minimum...
