The proposed rule provided technical criteria for vertical and horizontal standing supports....
Search Results "Horizontal Exit"
Filters
Commonly Searched Documents
-
2. Standing Supports
-
Corbin Russwin Inc. Access 600 RNE1 Electrified Door Hardware
The Access 600 RNE1 seamlessly integrates a full range of locks into your Wiegand Access Control System – from mortise locks to cylindrical locks and exit devices – all Grade 1 Corbin Russwin...
-
NFPA
, multiconductor cable), enclosure, or raceway only under the following conditions: (1) For a distance not to exceed 10 ft (3.0 m) where the outgoing and return conductors enter or exit...
-
ASME
The provisions for escalators require that at least two flat steps be provided at the entrance and exit of every escalator and that steps on escalators be demarcated by yellow lines 2 inches...
-
11B-410.1 General
Platform lifts shall not be attendant-operated and shall provide unassisted entry and exit from the lift. Advisory 11B-410.1 General....
-
Lutron Sivoia QS Wireless Shading System
control the entire family of Lutron automated window treatments, including roller shades, Venetian blinds, traditional drapery tracks, Kirbé® Vertical Drapery System, tensioned shades, horizontal...
-
Visible Alarms
., locker rooms, break rooms, cafeterias, toilet rooms, corridors to exits, and other common use spaces) were required to be accessible under the 1991 Standards; areas in which employees...
-
Safety
Those individuals operating a Segway within a Federal building must remain in control at all times and must exercise caution when turning corners and entering or exiting elevators. ...
-
Transfer Platforms
inches (610 mm) wide Minimum 14 inches (355 mm) deep Unobstructed side Adding a transfer step that leads to the ground's surface increases access for children exiting...
-
Driving Ranges
stations or practice teeing grounds are provided, at least five percent, but not less than one, of the practice teeing grounds must be accessible and provide space for a golf car to enter and exit...
-
B. Information about the Aircraft
., exit rows); Any limitation on the availability of storage facilities in the cabin or in the cargo bay for mobility aids or other equipment commonly used by an individual with...
-
Doors [4.35.3]
While turning space is not required wholly within rooms with curtained openings, it should be available so that users can easily enter and exit the space....
-
1134A.4 Sufficient maneuvering space
required to be adaptable shall provide sufficient maneuvering space for a person using a wheelchair or other mobility aid to enter and close the door, use the fixtures, reopen the door and exit...
-
1134A.4 Sufficient maneuvering space
required to be adaptable shall provide sufficient maneuvering space for a person using a wheelchair or other mobility aid to enter and close the door, use the fixtures, reopen the door and exit...
-
2. Analysis of footrest clearance height and depth
Three dimensions were computed on the right-side for the sub-set of wheelchairs with footrests: Abdomen-Castor edge depth: measured as the horizontal distance from the abdomen to...
-
11B-810.5.3 Platform and vehicle floor coordination
In light rail, commuter rail, and intercity rail systems where it is not operationally or structurally feasible to meet the horizontal gap or vertical difference requirements of part 1192...
-
810.5.3 Platform and Vehicle Floor Coordination
In light rail, commuter rail, and intercity rail systems where it is not operationally or structurally feasible to meet the horizontal gap or vertical difference requirements of part 1192...
-
11B-810.5.3 Platform and vehicle floor coordination
In light rail, commuter rail, and intercity rail systems where it is not operationally or structurally feasible to meet the horizontal gap or vertical difference requirements of part 1192...
-
11B-810.5.3 Platform and vehicle floor coordination
In light rail, commuter rail, and intercity rail systems where it is not operationally or structurally feasible to meet the horizontal gap or vertical difference requirements of part 1192...
-
307.2 Protrusion Limits
Objects with leading edges more than 27 inches (685 mm) and not more than 80 inches (2030 mm) above the finish floor or ground shall protrude 4 inches (100 mm) maximum horizontally into...
-
11B-1002.4.3 Gaps
coordinated so that, when amusement rides are at rest in the load and unload position, the vertical difference between the floors shall be within plus or minus 5/8 inches (15.9 mm) and the horizontal...
-
11B-307.2 Protrusion limits
Objects with leading edges more than 27 inches (686 mm) and not more than 80 inches (2032 mm) above the finish floor or ground shall protrude 4 inches (102 mm) maximum horizontally into...
-
307.2 Protrusion Limits
Objects with leading edges more than 27 inches (685 mm) and not more than 80 inches (2030 mm) above the finish floor or ground shall protrude 4 inches (100 mm) maximum horizontally into...
-
1002.4.3 Gaps
coordinated so that, when amusement rides are at rest in the load and unload position, the vertical difference between the floors shall be within plus or minus 5/8 inches (16 mm) and the horizontal...
