high transfer position of 25 inches; (3) at least four additional transfer positions located between the low and high transfer positions and separated by one inch minimum increments; (4) measured...
Search Results "Mitigating Measures"
Filters
Commonly Searched Documents
-
M302.2.1 Adjustability (Section-by-Section Analysis)
-
407.2.2.3 Audible Signals
The audible signal and verbal annunciator shall be 10 dB minimum above ambient, but shall not exceed 80 dB, measured at the hall call button. EXCEPTIONS: 1....
-
407.2.2.3 Audible Signals
The audible signal and verbal annunciator shall be 10 dB minimum above ambient, but shall not exceed 80 dB, measured at the hall call button. EXCEPTIONS: 1....
-
Supporting Documents for the Medical Diagnostic Equipment Accessibility Standards Advisory Committee Report
Subcommittee Report - Weight Scales IDeA Center Memo – Transfer Surface Dimensions IDeA Center Memo - Mammography Knee Clearance Depth and Footrest Clearance IDeA Center Memo - Wheelbase Measurements...
-
Is a transportation operator required to procure vehicles with lifts that have a design load of more than 600 pounds?
No. 49 CFR Part 38 continues to require that lifts have a minimum design load of 600 pounds and that the lift platform accommodate a wheelchair measuring 30 inches by 48 inches....
-
Is a transportation operator required to procure vehicles with lifts that have a design load of more than 600 pounds?
No. 49 CFR Part 38 continues to require that lifts have a minimum design load of 600 pounds and that the lift platform accommodate a wheelchair measuring 30 inches by 48 inches....
-
If the Passenger Poses a Direct Threat to the Health and Safety of Others
that person to provide a medical certificate stating that the disease at its current stage would not be transmittable during the normal course of a flight or, if applicable, describing measures...
-
11B-411.2.1.2.3 Accessibility function button
The dots shall be spaced ¼ inch (6.4 mm), measured center to center, in the form of an equilateral triangle with a vertex pointing up. ...
-
11B-411.2.2.2 Verbal identification
Auditory volume shall be at least 10 dB above ambient sound level, but shall not exceed 80 dB, measured 36 inches (914 mm) in front of the elevator entrance and at 48 inches (1219 mm) above...
-
407.2.2.3 Audible Signals
The audible signal and verbal annunciator shall be 10 dB minimum above ambient, but shall not exceed 80 dB, measured at the hall call button. EXCEPTIONS: 1....
-
1132A.9 Smooth surface
Swinging door or gate surfaces within 10 inches (254 mm) of the finish floor or ground measured vertically shall have a smooth surface on the push side extending the full width of the door...
-
703.3.1 Dimensions and Capitalization
Table 703.3.1 Braille Dimensions Measurement Range Minimum in Inches Maximum in Inches Dot base diameter 0.059...
-
Forward Reach [4.2.5]
Forward reaches are measured to the edge of available clear floor space. This accommodates high and low reaches and assumes some forward bending....
-
Printable Room Layouts
Measurements shown are adequate for ensuring accessibility, but more space is highly recommended for aisles, paths between chairs and tables, around the perimeter of the room, and around...
-
C. Defendants' Transaction Counter
“The counter uniformly measures less than 36 inches high.” Id. The submissions from the Court and the parties do not clearly state the length of the transaction counter as built....
-
5.2 Distributing Receivers
Taking appropriate hygienic measures after receivers are returned (e.g. spraying or wiping foam cushions with an antiseptic solution and replacing disposable cushions)....
-
11B-411.2.2.2 Verbal identification
Auditory volume shall be at least 10 dB above ambient sound level, but shall not exceed 80 dB, measured 36 inches (914 mm) in front of the elevator entrance and at 48 inches (1219 mm) above...
-
11B-411.2.2.2 Verbal identification
Auditory volume shall be at least 10 dB above ambient sound level, but shall not exceed 80 dB, measured 36 inches (914 mm) in front of the elevator entrance and at 48 inches (1219 mm) above...
-
Handbook of Construction Tolerances by David Kent Ballast FAIA, CSI
techniques developed since the book was first published, the Second Edition of this easy-to-use reference features: More than 100 drawings illustrating the tolerance concepts New sections on measuring...
-
Better Living LINEA Luxury Soap Dispenser
chamber lifts off the wall for easy re-filling Auto-lock feature prevents chamber from being accidentally bumped off bracket Rust-proof solid metal features Pump pre-measures...
-
Just Manufacturing Classroom Concealed Ledgemount Single Handle Restricted Swing Faucet
Classroom faucets feature rigid spouts, or restricted swing spouts, providing preventative measures against wet counter tops in the classroom....
-
Precision Safe Sidewalks LLC Sidewalk Trip Hazard Repair Service
Our service, unlike other approaches, accurately measures each offset to ensure that we achieve the slope requested by our customers....
-
M-D Building Products, Inc. GEN2 SmartTool™ Digital Level
Dependable, Accurate, Measures All Angles....
-
AJW Architectural Products U109 16 oz. Plastic Bulb Liquid Soap Dispenser - Surface Mounted
Will dispense a pre-measured amount of soap that is drip free. Globe: Translucent, polyethylene that is shatterproof and corrosion resistant....
