The spout shall provide a flow of water 4 inches (100 mm) high minimum and shall be located 5 inches (125 mm) maximum from the front of the unit....
Search Results "Expected Maximum Flight Duration"
Filters
Commonly Searched Documents
-
602.6 Water Flow
-
604.7 Dispensers
Toilet paper dispensers shall comply with 309.4 and shall be 7 inches (180 mm) minimum and 9 inches (230 mm) maximum in front of the water closet measured to the centerline of the dispenser...
-
Seat Heights
Seat Heights: Transfer platforms in play areas need to be between 11 and 18 inches maximum above the ground (ADA-ABA Section 1008.3.1.2)[7]....
-
602.6 Water Flow
The spout shall provide a flow of water 4 inches (100 mm) high minimum and shall be located 5 inches (125 mm) maximum from the front of the unit....
-
11B-602.6 Water flow
The spout shall provide a flow of water 4 inches (102 mm) high minimum and shall be located 5 inches (127 mm) maximum from the front of the unit....
-
11B-602.6 Water flow
The spout shall provide a flow of water 4 inches (102 mm) high minimum and shall be located 5 inches (127 mm) maximum from the front of the unit....
-
11B-602.6 Water flow
The spout shall provide a flow of water 4 inches (102 mm) high minimum and shall be located 5 inches (127 mm) maximum from the front of the unit....
-
Watchdog The RELOCATOR Fire Alarm Pull Station
The ADA requires pull stations to be mounted a maximum of 54” for wheelchair side access and 48” maximum for front access....
-
Corbin Russwin Inc. DC46900 Series Safeguard Door Closers
For doors flush with frame, or with 1/8" maximum reveal on pull side. Minimum top rail 2-3/16". DC46925 Unit Push side mounted unit for right or left hand doors....
-
3. Stowage Space for Wheelchairs
comments pointed out, requiring space for one wheelchair does not completely solve this problem for all passengers with disabilities, doing so does help at least one such passenger per flight...
-
2. Accessible lavatories
Particularly given that single-aisle aircraft often make lengthy flights (e.g., across North America, some trans-oceanic flights), it is clear that providing accessible lavatories on single-aisle...
-
382.9 What may foreign carriers do if they believe a provision of a foreign nation’s law prohibits compliance with a provision of this Part?
This may occur, for example, in the case of U.S. carriers who must ensure compliance with the service-related provisions of this Part on code share flights between two foreign points operated...
-
705.1.1 Dome Size
Truncated domes in a detectable warning surface shall have a base diameter of 0.9 inch (23 mm) minimum and 1.4 inches (36 mm) maximum, a top diameter of 50 percent of the base diameter minimum...
-
705.1.1 Dome Size
Truncated domes in a detectable warning surface shall have a base diameter of 0.9 inch (23 mm) minimum and 1.4 inches (36 mm) maximum, a top diameter of 50 percent of the base diameter minimum...
-
804.3.2 Height
The kitchen work surface shall be 34 inches (865 mm) maximum above the finish floor or ground....
-
1.1.3
1.1.3 A maximum overall design running slope for exterior accessible surfaces (other than ramps), such as sidewalks, of 4% (approximately 1:25) is recommended....
-
What do I do if I believe that a passenger’s assertions about having a disability or a service animal are not credible?
In the rare instance that a service animal would raise a concern regarding flight safety, the CRO may consult with the pilot-in-command....
-
11B-703.3.1 Dimensions and capitalization
TABLE 11B-703.3.1 BRAILLE DIMENSIONS MEASUREMENT RANGE MINIMUM IN INCHES MAXIMUM IN INCHES Dot base diameter...
-
Discrimination is Prohibited
[Sec. 382.7(a)(4)] Carriers cannot limit the number of passengers with a disability on a given flight....
-
11B-603.4 Coat hooks, shelves and medicine cabinets
Shelves shall be located 40 inches (1016 mm) minimum and 48 inches (1219 mm) maximum above the finish floor....
-
11B-609.2.2 Non-circular cross section
Grab bars with non-circular cross sections shall have a cross-section dimension of 2 inches (51 mm) maximum and a perimeter dimension of 4 inches (102 mm) minimum and 4.8 inches (122 mm)...
-
11B-505.7.2 Non-circular cross sections
Handrail gripping surfaces with a non-circular cross section shall have a perimeter dimension of 4 inches (102 mm) minimum and 6¼ inches (159 mm) maximum, and a cross-section dimension of...
-
11B-703.5.7 Stroke thickness
Stroke thickness of the uppercase letter “I” shall be 10 percent minimum and 20 percent maximum of the height of the character. [2010 ADAS] 703.5.7 Stroke Thickness....
-
11B-703.7.2.6.4 Edges and vertices on geometric symbols
Edges shall be eased or rounded at 1/16 inch (1.59 mm) minimum, or chamfered at 1/8 inch (3.2 mm) maximum....
