Stair treads shall comply with Section 11B-302. Changes in level, slopes exceeding 1:48, and detectable warnings shall not be permitted. Exception: Reserved.
Search Results "Side Transfer Surface"
Filters
Commonly Searched Documents
-
11B-504.4 Tread surface
-
Shredded Rubber
The surface material used as a play safety surface has gained some popularity as a means to reuse tires. ...
-
1014.3.2 Slope
The slope of the floor surface shall not be steeper than 1:48 in any direction....
-
1014.3.2 Slope
The slope of the floor surface shall not be steeper than 1:48 in any direction....
-
Non Slip Safety Solutions
The end result is a floor surface engineered for lasting beauty and trouble-free maintenance....
-
Scoping [4.1.2(4), 4.1.3(3)]
Requirements in 4.5 apply to accessible routes and spaces, including ramps, elevators, platform lifts, and clear floor space. These requirements apply to interior and exterior...
-
Rockwood Manufacturing Company K2060 - .060" Thick Plastic Kick Plate - Heavy Duty
Width of Plates: Push Side - 2" less than door width. Pull Side - 1-1/2" less than door width....
-
M305.2.7 Clearance
Clearance between the transfer support gripping surface and adjacent surfaces or obstructions shall be 1 ½ inches (38 mm) minimum....
-
Cross Slope: ADA Standard Section 405.3
Section 405.3 covers the current ADA Standards for cross slope requirements on ramps.
-
Aluminum Heavy Duty Wheels n' Heels® Metro Grating
Metro has an even greater strength to weight ratio, and much improved aesthetic appeal, since there are now no welds on the top surface....
-
11B-904.3.3 Check writing surfaces
Where provided, check writing surfaces shall comply with Section 11B-902.3....
-
11B-904.3.3 Check writing surfaces
Where provided, check writing surfaces shall comply with Section 11B-902.3....
-
11B-904.3.3 Check writing surfaces
Where provided, check writing surfaces shall comply with Section 11B-902.3....
-
Don-Jo Mfg., Inc. Commercial Kick Plates 90
Options MAG - magnetic backing for metal doors, SM - double face tape (scotch mount), TEK - self drilling screws, CSK - countersunk holes, Torx - security torx screw,4BE - bevel 4 sides...
-
11B-226.3 Dining surfaces exceeding 34 inches in height
Where food or drink is served for consumption at a counter exceeding 34 inches (864 mm) in height, a portion of the main counter 60 inches (1525 mm) minimum in length shall be...
-
11B-226.3 Dining surfaces exceeding 34 inches in height
Where food or drink is served for consumption at a counter exceeding 34 inches (864 mm) in height, a portion of the main counter 60 inches (1525 mm) minimum in length shall be...
-
11B-226.3 Dining surfaces exceeding 34 inches in height
Where food or drink is served for consumption at a counter exceeding 34 inches (864 mm) in height, a portion of the main counter 60 inches (1525 mm) minimum in length shall be...
-
302.3 Openings
Openings in floor or ground surfaces shall not allow passage of a sphere more than ½ inch (13 mm) diameter except as allowed in 407.4.3, 409.4.3, 410.4, 810.5.3 and 810.10....
-
M305.2.7 Clearance (Section-by-Section Analysis)
surface....
-
302.3 Openings
Openings in floor or ground surfaces shall not allow passage of a sphere more than ½ inch (13 mm) diameter except as allowed in 407.4.3, 409.4.3, 410.4, 810.5.3 and 810.10....
-
11B-703.4.2 Location
Where there is no wall space at the latch side of a single door or at the right side of double doors, signs shall be located on the nearest adjacent wall....
-
AccessRec DuraDeck 2 Molded Plastic Mat Ground Surface
Sections are engineered to provide ground protection and access over soft surfaces and will provide a firm support base and traction for numerous activities....
-
M305.2.8 Fittings (Section-by-Section Analysis)
Further, this commenter noted that the requirement conflicts with proposed M302.2.3, which allows for temporary obstructions such as armrests, footrests, and side rails that can be repositioned...
-
ADA Tolerances - Related Industry Standards
[See subsections ...]
