These commenters recommended that where only a portion of counters are made accessible, the accessible height should be 31 inches maximum....
Search Results "Counter Depth"
Filters
Commonly Searched Documents
-
Table Surface Height
-
A4.1.1(3) Areas Used Only by Employees as Work Areas
., laboratories, service counters, ticket booths), 5%, but not less than one, of each type of work station should be constructed so that an individual with disabilities can maneuver within...
-
Employee Work Areas [§206.2.8]
This applies to the size of work areas as defined by permanently installed walls, partitions, counters, casework, or furnishings, but not modular partitions or furnishings, including systems...
-
Neo-Metro Commercial Wall Mounted Neo-Basin 8935 Series
Model 8935 features 2.5" extended counter on both sides while Model 8936 does not. A trap enclosure is standard on both versions....
-
Oval Window Audio Portable InfoLoop Hearing System
microphone Automatic gain control Noise gating electronics Loop wire antenna 5-8 hour rechargeable battery The Portable InfoLoop is ideal for meetings (left) information/sales counters...
-
ASI Global Partitions Plastic Laminate Partitions
Plastic laminate is available in all four installation styles and a variety of designer colors to complement vanities and counter tops....
-
Tork Toilet Seat Cover Dispenser, 1/2 Fold
Product Data System - V1 - toilet seat cover system Material - Plastic Height - 11.5 in Width - 16 in Depth - 3 in Color - White...
-
Priority 3: Toilet Rooms
Word Fillable Form (2.4MB) Word Non-Fillable Form (2.2MB) PDF Non-Fillable Form (0.7MB)
-
11B-205.1 General
Where two or more outlets are provided in a kitchen above a length of counter top that is uninterrupted by a sink or appliance, one outlet shall not be required to comply with 309....
-
Soiltac Liquid Topical
The stabilizer has a penetration depth of 1/8 inch. The first noticeable signs of change for this surface came after the first heavy rainfall at the March 2008 testing....
-
809.2.2 Turning Space
EXCEPTION: Turning space shall not be required in exterior spaces 30 inches (760 mm) maximum in depth or width. Advisory 809.2.2 Turning Space....
-
11B-705.2 Detectable directional texture
The depth of the texture shall not be less than 36 inches (914 mm). FIGURE 11B-705.2 ‡‡ DETECTABLE DIRECTIONAL TEXTURE...
-
M303.2.2 Width (Section-by-Section Analysis)
(Significant Changes – Width and Depth of Wheelchair Spaces), and discussed briefly below....
-
Section 5 References
“Revised Knee Clearance Depth and Footrest Clearance dimensions for sizing of mammography equipment.” Memorandum. April 23, 2013....
-
809.2.2 Turning Space
EXCEPTION: Turning space shall not be required in exterior spaces 30 inches (760 mm) maximum in depth or width. Advisory 809.2.2 Turning Space....
-
Teeing Grounds
A rectangular area usually two club-lengths in depth, the teeing ground’s borders are defined by the outside limits of two “tee-markers.”...
-
5.3.2 Transfer Sides Recommendations for M301
The transfer surface shall be located to provide options to transfer from a mobility device onto one short side (depth) and one long side (width) of the surface....
-
5.7.1 Lift Compatibility Clearance in Base for M301
Where the width of the examination surface is less than 36 inches, the clearance depth shall extend the full width of the equipment....
-
809.2.2 Turning Space
EXCEPTION: Turning space shall not be required in exterior spaces 30 inches (760 mm) maximum in depth or width. Advisory 809.2.2 Turning Space....
-
15. Can I store my lift and bring it out only when it is requested by a person with a disability?
In addition, the ADA Standards specify that a lift must be located at the proper water depth and with the necessary space around it to maneuver a wheelchair....
-
11B-705.2 Detectable directional texture
The depth of the texture shall not be less than 36 inches (914 mm)....
-
4.3.6 Reach Limits
For the accommodation model of forward reach, the depth of knee clearance needed to accommodate different proportions of the sample can be determined by the columns with negative offset...
