Throughout this NPRM, the current, legally enforceable ADA Standards will be referred to as the "1991 Standards." 28 CFR part 36, App....
Search Results "Vertical Reference Plane"
-
Overview
-
504.5 Nosings
Risers shall be permitted to slope under the tread at an angle of 30 degrees maximum from vertical....
-
703.2.5 Character Height
Character height measured vertically from the baseline of the character shall be 5/8 inch (16 mm) minimum and 2 inches (51 mm) maximum based on the height of the uppercase letter "I"....
-
R405.1 General
Clearances are measured in relation to the usable clear space, not necessarily to the vertical support for an element....
-
7.4.5.1 Size
Vertical alignment at the intersection of the trails that form the T-shaped space shall be nominally level....
-
Parking and Passenger Loading Zones [4.6]
Accessibility also includes the appropriate designation and location of spaces and passenger loading zones, their connection to an accessible route, and vertical clearance for vans....
-
Spout Location [4.15.3]
The trajectory of water flow must be vertically "parallel" or "nearly parallel" to the face of the unit....
-
§ 38.73(d)(1) Requirements
Vertical alignment may be accomplished by vehicle air suspension, automatic ramps or lifts, or any combination....
-
11B-703.2.5 Character height
Character height measured vertically from the baseline of the character shall be 5/8 inch (15.9 mm) minimum and 2 inches (51 mm) maximum based on the height of the uppercase letter “I”....
-
504.5 Nosings
Risers shall be permitted to slope under the tread at an angle of 30 degrees maximum from vertical....
-
1008.3.2.3 Transfer Supports
Some examples of supports include a rope loop, a loop type handle, a slot in the edge of a flat horizontal or vertical member, poles or bars, or D rings on the corner posts....
-
703.2.5 Character Height
Character height measured vertically from the baseline of the character shall be 5/8 inch (16 mm) minimum and 2 inches (51 mm) maximum based on the height of the uppercase letter "I"....
-
10.4 Coordination Procedures to Avoid Duplicative Complaint Processing Under the ADA and the Rehabilitation Act
OFCCP will process such complaints/charges for EEOC, with certain exceptions specified in the regulation, where OFCCP will refer the charge to EEOC....
-
1118B.4
Changes in level up to 1/4 inch (6.4 mm) may be vertical and without edge treatment [see Figure 11B-5E(c)]....
-
C102 Referenced Standards (Section-by-Section Analysis)
Incorporation by reference of these standards would be an improvement from the existing 255 Guidelines, which contain no referenced standards....
-
Organization of This Rule
Throughout this rule, the original ADA Standards, which are republished as Appendix D to 28 CFR part 36, will be referred to as the ‘‘1991 Standards.’’...
-
4.2 Stretchers
First, to serve these multiple purposes, the current configuration of stretchers must accommodate the vertical height needs of numerous components, including (Figure 3.1): the basic elements...
-
11B-220.2 Point-of-sale devices
Corrects code references for applicable technical requirements for point-of-sale devices, and adds requirement for point-of-sale devices at electric vehicle charging stations....
-
7.3 Definitions
All trail-related definitions used in the FSTAG are from the Forest Service Manual or Handbook, the Forest Service Infra Trails Module, Trail Assessment and Condition Survey (TRACS) reference...
-
410.6.3.2 VoIP Using SIP
Where ICT interoperates with Voice over Internet Protocol (VoIP) products or systems using Session Initiation Protocol (SIP), real-time text shall conform to RFC 4103 (incorporated by reference...
-
PEDESTRIAN WAY
Reference(s): Government Code Sections 4450 through 4461 and Health and Safety Code Section 18949.1....
-
Stanley QRM 100 Series Grade 1 Extra Heavy Duty Exit Devices
In addition, all exit devices are offered in rim, rim fire, surface vertical rod, surface vertical rod fire and surface vertical-less bottom rod configurations....
-
11B-703.2.5 Character height
Character height measured vertically from the baseline of the character shall be 5/8 inch (15.9 mm) minimum and 2 inches (51 mm) maximum based on the height of the uppercase letter “I”. ...
-
A7. Curb Ramps
[ADA Stds 4.7.2] Note: 1:12 is one inch of vertical height for each 12 inches in length. Yes _____ No _____...
