Viewing distance shall be measured as the horizontal distance between the character and an obstruction preventing further approach towards the sign....
Search Results "Horizontal Exit"
Filters
Commonly Searched Documents
-
11B-703.8.4 Character height
-
5.4.4 Transfer Support Distance from Transfer Surface Recommendations for M301 and M302
The gripping surface measurement is horizontal from the adjacent edge of the transfer surface (see figure 5.4.1). NPRM Proposed Provision: M305.2.1 Location....
-
11B-703.8.4 Character height
Viewing distance shall be measured as the horizontal distance between the character and an obstruction preventing further approach towards the sign....
-
11B-703.8.4 Character height
Viewing distance shall be measured as the horizontal distance between the character and an obstruction preventing further approach towards the sign....
-
BYO Recreation Inc. Fun Hoop
This Accessible Fun Hoop is one large basket with multiple exits and is closer to the ground than our other Fun Hoop....
-
11B-608.3 Grab bars
Where multiple grab bars are used, required horizontal grab bars shall be installed at the same height above the finish floor....
-
11B-404.2.10 Door and gate surfaces
Parts creating horizontal or vertical joints in these surfaces shall be within 1/16 inch (1.6 mm) of the same plane as the other and be free of sharp or abrasive edges....
-
404.2.10 Door and Gate Surfaces
Parts creating horizontal or vertical joints in these surfaces shall be within 1/16 inch (1.6 mm) of the same plane as the other....
-
5.4.2.2 Transfer and Positioning Support Length Recommendations for Imaging Equipment with Transfer Surfaces
Rational for the recommendation A transfer support (for transfer surfaces less than or equal to 24” deep) is to extend horizontally along the side of the patient scanning/imaging table...
-
4. Wheelchair seat depth
Wheelchair seat depth For this study, wheelchair seat depth was calculated as the horizontal distance from the proximal (i.e., towards the rear) edge to the distal (i.e., towards the...
-
2.2 Lighting Conditions
On each trial one measurement of horizontal illuminance was manually recorded from a Minolta T-1 Illuminance meter....
-
11B-404.2.10 Door and gate surfaces
Parts creating horizontal or vertical joints in these surfaces shall be within 1/16 inch (1.6 mm) of the same plane as the other and be free of sharp or abrasive edges....
-
11B-608.3 Grab bars
Where multiple grab bars are used, required horizontal grab bars shall be installed at the same height above the finish floor....
-
11B-608.3 Grab bars
Where multiple grab bars are used, required horizontal grab bars shall be installed at the same height above the finish floor....
-
11B-404.2.10 Door and gate surfaces
Parts creating horizontal or vertical joints in these surfaces shall be within 1/16 inch (1.6 mm) of the same plane as the other and be free of sharp or abrasive edges....
-
1132A.4.1 Thresholds
Thresholds at the primary entry and required exit doors shall be no higher than ½ inch (12.7 mm)....
-
Elevated Play Component
This climber is considered an elevated component since it can be approached or exited from the ground level or above grade from a platform or deck on a composite play structure...
-
Contents:
breathing, allergies, hearing, seeing, walking, understanding or chronic conditions) may have difficulty or be unable to: use stairwells hear alarms see or read exit...
-
68.30(2) Places Used Primarily for Religious Rituals
This exemption does not apply to the following: parking facilities, accessible routes, walkways, hallways, toilet facilities, entrances, public telephones, drinking fountains, and exits;...
-
1132A.5.2 Strike edge maneuvering space at doors
The width of the level area at the exterior side of the primary entry door and any required exit doors shall comply with Section 1126A....
-
11B-703.7.2.7 Pedestrian traffic-control buttons
Pole-supported pedestrian traffic-control buttons shall be identified with color coding consisting of a textured horizontal yellow band 2 inches (51 mm) in width encircling the pole, and...
-
4.28.3(7)
(7) In general, no place in any room or space required to have a visual signal appliance shall be more than 50 ft (15 m) from the signal (in the horizontal plane)....
-
4.9.4(2)
At the bottom, the handrail shall continue to slope for a distance of the width of one tread from the bottom riser; the remainder of the extension shall be horizontal (see Fig. 19(c) and...
-
§ 38.53(d)(1) Requirements
Where new vehicles will operate in new stations, the design of vehicles shall be coordinated with the boarding platform design such that the horizontal gap between each vehicle door at rest...
