Such light(s) shall be shielded to protect the eyes of entering and exiting passengers....
Search Results "Horizontal Exit"
Filters
Commonly Searched Documents
-
§ 38.157(b)
-
Don-Jo Mfg., Inc. 2-3/4" Hospital Latch 4500
Shelf pack 1 Features UL Listed, Works with 1-3/4" doors, Lever projection 3-1/4", Non Handed, Push/Pull latch can be mounted with the handles up, down or horizontal...
-
505.10.2 Top Extension at Stairs
At the top of a stair flight, handrails shall extend horizontally above the landing for 12 inches (305 mm) minimum beginning directly above the first riser nosing....
-
f-v
If a ramp is more than 30 feet long, is a level landing at least 60 inches long provided at every 30 feet of horizontal length?...
-
4d.
If a ramp is more than 30 feet long, is a level landing at least 60 inches long provided every 30 feet of horizontal length?...
-
6d. Ramp Length
If a ramp is more than 30 feet long, is a level landing at least 60 inches long provided every 30 feet of horizontal length?...
-
Extensions
Handrails that are not continuous must have horizontal extensions at both the top and bottom of the ramp at least 12 inches long that are rounded or returned smoothly to walls, posts, or...
-
11B-809.10.5.2 Reinforcement for grab bars
Grab bar backing shall be installed horizontally to permit the installation of a 48-inch (1219 mm) grab bar with each end 6 inches (152 mm) maximum from the end walls of the bathtub....
-
III-7.3110 Work areas
The requirement for work areas is that they be designed so that individuals with disabilities can approach, enter, and exit the areas....
-
Handrail Requirements
An exception permitted brackets and balusters attached to the bottom of a handrail provided they did not obstruct more than 20% of the handrail length, their horizontal projection was at...
-
Transfer Sides (M301.2.3 and M302.2.3)
This is consistent with ANSI/AAMI HE 75 which recommends that the “base of any patient-support platform should not extend horizontally beyond the edge of the support surface . . ....
-
1. What is the effective compliance date of the ADA standards for accessible pools?
However, and in response to public comments and concerns, the Department has extended the date for compliance for the requirements related to the provision of accessible entry and exit to...
-
e-ii
Does the floor area of the elevator car have space to enter, reach the controls, and exit?...
-
5b.
Does the floor area of the elevator car provide space for wheelchair users to enter, reach the controls, and exit the car?...
-
A4. Vertical Clearance
is there vertical clearance of at least 98 inches (8 feet - 2 inches) for the vehicle route to the parking space, the parking space, the access aisle and along the vehicle route to the exit...
-
§ 38.119(b)
Such lights shall be shielded to protect the eyes of entering and exiting passengers....
-
§ 38.81(c)
Such lights shall be located below window level and shielded to protect the eyes of entering and exiting passengers....
-
1009.10 Directional signage
At exits serving a required accessible space but not providing an approved accessible means of egress. 2. At elevator landings. 3. Within areas of refuge....
-
3. Buttock-Popliteal Length
Buttock-Popliteal Length For this study, an estimate of buttock-popliteal length was calculated as the horizontal distance from the proximal (rear) edge of the wheelchair seat cushion...
-
404.2.10 Door and Gate Surfaces
Parts creating horizontal or vertical joints in these surfaces shall be within 1/16 inch (1.6 mm) of the same plane as the other. Cavities created by added kick plates shall be capped....
-
M305.2 Transfer Supports
M305.2 Transfer Supports M305.2.2 Transfer Supports Structural Strength Proposed requirement: Transfer supports and their connections shall be capable of resisting vertical and horizontal...
-
711.3.2 Membrane penetrations
By a horizontal distance of not less than 24 inches (610 mm); 1.2....
-
404.2.10 Door and Gate Surfaces
Parts creating horizontal or vertical joints in these surfaces shall be within 1/16 inch (1.6 mm) of the same plane as the other....
-
Transfer Supports (M301.3.1, M302.3.1, and M305.2)
M305.2.2 would require the transfer supports and their connections to be capable of resisting vertical and horizontal forces of 250 pounds applied to all points of the transfer support....
