Together these companies produce the vast majority of the hardware items used in the nation’s commercial and institutional buildings -- from hinges and locks to door controls and exit devices...
Search Results "Horizontal Exit"
Commonly Searched Documents
- Builders Hardware Manufacturers Association (BHMA)
- Window Ease
- Southwest Home Products Window Ease Latching System
-
PATH OF TRAVEL
[DSA-AC] An identifiable accessible route within an existing site, building or facility by means of which a particular area may be approached, entered and exited, and which connects a particular...
-
Re: Stair widths
This 48 inches theoretically provides enough room for two or three people to carry a person with mobility issues down to the level of exit discharge. ...
-
238.3 Practice Putting Greens, Practice Teeing Grounds, and Teeing Stations at Driving Ranges
percent, but no fewer than one, of practice putting greens, practice teeing grounds, and teeing stations at driving ranges shall be designed and constructed so that a golf car can enter and exit...
-
B4
is there vertical clearance of at least 98 inches (8 feet - 2 inches) for the vehicle route to the parking space, the parking space, the access aisle, and along the vehicle route to the exit...
-
A4.34.2 MINIMUM REQUIREMENTS
An accessible second exit to dwelling units provides an extra margin of safety in a fire....
-
§ 38.31(c)
Such light(s) shall be shielded to protect the eyes of entering and exiting passengers....
-
11B-903.4 Back support
Back support shall be 2½ inches (64 mm) maximum from the rear edge of the seat measured horizontally. [2010 ADAS] 903.4 Back Support. ...
-
1009.9 Signage
Where exit sign illumination is required by Section 1013.3, the signs shall be illuminated....
-
1.1.3 Walk running slope
Calculate the slope using the horizontal distance between elevation points and the difference between the elevations at those points (i.e. the rise over the run)....
-
PLATFORM
entertainment; the head table for special guests; the raised area for lecturers and speakers; boxing and wrestling rings; theater-in-the-round stages; and similar purposes wherein, other than horizontal...
-
(1)(c)
(c) A grab bar at least 24 inches (610 mm) long should be mounted behind the water closet, and a horizontal grab bar at least 40 inches (1015 mm) long should be mounted on at least one side...
-
PLATFORM
entertainment; the head table for special guests; the raised area for lecturers and speakers; boxing and wrestling rings; theater-in-the-round stages; and similar purposes wherein, other than horizontal...
-
1015.2 Where required
equipment platforms, aisles, stairs, ramps and landings that are located more than 30 inches (762 mm) measured vertically to the floor or grade below at any point within 36 inches (914 mm) horizontally...
-
Emergency Planning
detail procedures for providing evacuation assistance to people who would have difficulty or who would be unable to: Use stairwells, Hear alarms, See exits...
-
1009.9 Signage
Where exit sign illumination is required by Section 1011.3, the signs shall be illuminated....
-
11B-240.2.2 Elevated play components
Some play components that are attached to a composite play structure can be approached or exited at the ground level or above grade from a platform or deck....
-
Surprise Drills
., blocked paths or exits), forcing people to use alternative routes. Performance of these drills should also be evaluated and feedback given to all participants. ...
-
Door Closers [4.13.10]
it may be difficult for a person with a disability to open a door against the resistance offered by a closer, it is important that the closing action be slow enough to allow entry and exit...
-
Elevators with Standby Power [IBC §1007.4 (2003), §1003.2.13.3 (2000)]
In buildings with four or more stories above or below the level of exit discharge, at least one accessible means of egress must be an elevator with standby power and emergency signaling...
-
1132A.4.1 Thresholds
Thresholds at the primary entry and required exit doors shall be no higher than ½ inch (12.7 mm)....
-
903.4 Back Support
Back support shall be 2 1/2 inches (64 mm) maximum from the rear edge of the seat measured horizontally. ...