FEATURES: Extruded aluminum base*abrasive filler Lengths to order, up to 10'-0" max. in one piece....
Search Results "Full Length Mirror"
Filters
Commonly Searched Documents
-
Spectra Safety Treads
-
Pilot Rock TPT Series End Accessible Twin Pedestal Table
Each table has two full-length bench seats and have the step over entry design. The suspended seat supports simplify maintenance and clean up around the tables. ...
-
Accessible Routes: ADA Standard Section 1007.2
Ramp landing length specified by 405.7.3 shall be permitted to be 48 inches (1220 mm) long minimum. 6....
-
Grab Bars: ADA Standard Section 604.5
Section 604.5 covers the current ADA Standards for grab bars that are used for water closets.
-
11B-405.8 Handrails
At door landings, handrails are not required on ramp runs less than 6 inches (152 mm) in rise or 72 inches (1829 mm) in length....
-
403.5.1 Clear Width
EXCEPTION: The clear width shall be permitted to be reduced to 32 inches (815 mm) minimum for a length of 24 inches (610 mm) maximum provided that reduced width segments are separated by...
-
607.2 Clearance
Clearance in front of bathtubs shall extend the length of the bathtub and shall be 30 inches (760 mm) wide minimum....
-
Running Slope
Running Slope—The ascent or descent of a trail segment expressed as a percentage of its length....
-
7.2.2 General Exception 2
For long-distance trails, this exception applies to the trail segments that are planned for construction or alteration in a given planning period, rather than over the entire length of the...
-
Appendix 2- Photos of Participants in the IDEA Center Research
of Participants in the IDEA Center Research Examples of High Seats: Examples of Very Large and Small Clear Floor Area Widths: Examples of Very Long Clear Floor Area Lengths...
-
Handrails [ADA Standards §504.6, §505]
Handrails [ADA Standards §504.6, §505] Specifications in the ADA Standards for handrail surfaces and clearances facilitate a power grip along the handrail length....
-
11B-505.2 Where required
At door landings, handrails are not required when the ramp run is less than 6 inches (152 mm) in rise or 72 inches (1829 mm) in length....
-
11B-213.3.1 Toilet compartments
Full-height partitions and door assemblies can comprise toilet compartments where the minimum required spaces are provided within the compartment. ◼...
-
11B-404.3 Automatic and power-assisted doors and gates
Full-powered automatic doors shall comply with ANSI/BHMA A156.10. Low-energy and power-assisted doors shall comply with ANSI/BHMA A156.19....
-
Two-Way Communication
The proposed rule included requirements for the cord length of provided handsets and instructions....
-
Benches
Benches must have seats that are a minimum of 20 inches to a maximum of 24 inches in depth and 42 inches minimum in length....
-
11B-904.4.1 Parallel approach
A clear floor or ground space complying with Section 11B-305 shall be positioned for a parallel approach adjacent to the 36 inch (914 mm) minimum length of counter....
-
Can you upgrade/expand an existing location without adhering to ADA standards?
The new accessibility requirements in the CBC are intended to provide full compliance with the requirements of the ADA....
-
§100.201a(a)
(a) The following standards are incorporated by reference into 24 CFR part 100 pursuant to 5 U.S.C. 552(a) and 1 CFR part 51, as though set forth in full....
-
5.1.6 Clear Floor or Ground Space
One full unobstructed side of the clear ground space shall adjoin or overlap the trail or ORAR, as applicable, or another clear ground space....
-
§ 37.139(d)(5)
In no case may full implementation be completed later than January 26, 1997....
-
Handrail Requirements
An exception permitted brackets and balusters attached to the bottom of a handrail provided they did not obstruct more than 20% of the handrail length, their horizontal projection was at...
-
1017.1 General
When an entity determines that a condition in 1019 does not permit full compliance with a specific provision in 1017 on a portion of a trail, the portion of the trail shall comply with the...
-
Section 35.151 New Construction and Alterations (Section-by-Section Analysis)
The Department will add a new section, designated as § 35.151(a)(2), to provide that full compliance with the requirements of this section is not required where an entity can demonstrate...
