Boarding and alighting areas shall provide a clear length of 2.4 m (8.0 ft) minimum, measured perpendicular to the curb or street or highway edge, and a clear width of 1.5 m (5.0 ft) minimum...
Search Results "Full Length Mirror"
-
R308.1.1.1 Dimensions
-
407.8.3.1 Unobstructed Forward Reach
Where the operable part is located at the leading edge of the maximum protrusion within the length of the vertical reference plane of the ICT, the operable part shall be 48 inches (1220...
-
2. Using the Tape Measure
Using the Tape Measure A metal tape measure is needed to measure the length, width, height, and depth of various elements....
-
N1
accessible route, at least 36 inches wide, that connects each of the shelter activity areas with the health units and medical care areas (it may narrow to 32 inches wide for up to 2 feet in length...
-
§ 38.35(a)
(a) Vehicles in excess of 22 feet in length, used in multiple-stop, fixed-route service, shall be equipped with a public address system permitting the driver, or recorded or digitized human...
-
American Specialties Zamac Recessed Soap Dish with Bar 0410-Z
All exposed surfaces shall be triple plated with copper, nickel and chrome to a mirror finish....
-
305.6 Approach
One full unobstructed side of the clear floor or ground space shall adjoin an accessible route or adjoin another clear floor or ground space....
-
7.2.1 General Exception 1
Where a condition in 7.1 prohibits full compliance with a specific requirement in 7.4 on a trail segment, that trail segment shall comply with the specific requirement to the maximum extent...
-
TERMS OF AGREEMENT
NOW, THEREFORE, for full and adequate consideration given and received, the United States, through the Civil Rights Division of the U.S....
-
Obstructed High Reach
Knee and toe space must extend the full depth of reach....
-
Height – M301.2.1 & M302.2.1
The final recommendation of the subcommittee to the full committee was a recommendation of 19 inches with a "best practice" standard of 17 inches....
-
R409.7 Cross Section
Where expansion joints are necessary for large spans of handrails, the expansion joint is permitted to be smaller than the specified cross section diameters for a 25mm (1 in) length....
-
407.12.3.2 Obstructed Forward Reach
Where the operable part is located beyond the leading edge of the maximum protrusion within the length of the vertical reference plane, the operable part shall conform to 407.12.3.2....
-
Cross Slope
The percentage of rise to length, which is the difference in elevation, when measuring the trail tread from edge to edge perpendicular to the direction of travel This may be expressed as...
-
11B-810.2.2 Dimensions
Bus stop boarding and alighting areas shall provide a clear length of 96 inches (2438 mm) minimum, measured perpendicular to the curb or vehicle roadway edge, and a clear width of 60 inches...
-
11B-607.2 Clearance
Clearance in front of bathtubs shall extend the length of the bathtub and shall be 48 inches (1219 mm) wide minimum for forward approach and 30 inches (762 mm) wide minimum for parallel...
-
Refuge Islands
"(29) However, recumbent bicycles, bicycles with trailers, and hand cycles all have 85th percentile lengths greater than 1.8 m (6 ft)....
-
1003.2.1 Boat Slips
Where an existing gangway or series of gangways is replaced or altered, an increase in the length of the gangway shall not be required to comply with 1003.2 unless required by 202.4....
-
1003.2.1 Boat Slips
Where an existing gangway or series of gangways is replaced or altered, an increase in the length of the gangway shall not be required to comply with 1003.2 unless required by 202.4....
-
1003.2.1 Boat Slips
Where an existing gangway or series of gangways is replaced or altered, an increase in the length of the gangway shall not be required to comply with 1003.2 unless required by 202.4....
-
Slopes and Resting Intervals for Beach Access Routes
Sections of beach access route of any length are allowed to have a running slope ratio of up to 1:20 (5 percent grade) (see figure 37)....
-
11B-1003.2.1 Boat slips
Exceptions: Where an existing gangway or series of gangways is replaced or altered, an increase in the length of the gangway shall not be required to comply with Section 11B-1003.2...
-
Guest Room Doors and Doorways: ADA Standard Section 224.1.2
Section 224.1.2 covers scoping requirements in the current ADA Standards for transient lodging guest room doors and doorways.
