When changes in level do occur, they shall be beveled with a slope no greater than 1 unit vertical in 2 units horizontal (50-percent slope)....
Search Results "Slope"
-
1131A.1 Changes in level not exceeding ½ inch
-
Passing Spaces [1017.4]
Nominally planar means on the same nominal table surface (same nominal geometric surface plane) and the slopes of the table surface correspond to the running slope and cross slope of the...
-
Transition Plates
Transition Plates Transition plates are sloping pedestrian walking surfaces located at the end of a gangway....
-
Maneuvering Space Where Ramps are Provided
The space must have a slope no steeper than 1:48 in all directions. ...
-
Transition Plates
Transition Plates Transition plates are sloping pedestrian walking surfaces located at the end of a gangway....
-
505.1 General
Handrails are not required on walking surfaces with running slopes less than 1:20....
-
704.11.1 Parapet construction
Where the roof slopes toward a parapet at a slope greater than two units vertical in 12 units horizontal (16.7-percent slope), the parapet shall extend to the same height as any portion...
-
11B-505.1 General
Handrails are not required on walking surfaces with running slopes less than 1:20....
-
505.1 General
Handrails are not required on walking surfaces with running slopes less than 1:20....
-
Attachment I: Program Access in Existing Facilities
Attachment I: Program Access in Existing Facilities
-
1131A.2 Changes greater than ½ inch
Changes in level greater than ½ inch (12.7 mm) shall be made by means of a sloped surface not greater than 1 unit vertical in 20 units horizontal (5-percent slope), or a ramp, elevator or...
-
1131A.1 Changes in level not exceeding ½ inch
When changes in level do occur, they shall be beveled with a slope no greater than 1 unit vertical in 2 units horizontal (50-percent slope)....
-
1018.1 General
The technical requirements address connections (1018.2); surface (1018.3); clear width (1018.4); obstacles (1018.5); openings (1018.6); slopes, including running slope (1018.7.1) and cross...
-
Rise
The maximum length of a run is determined by the rise (30 inches maximum) and the slope: Max. Rise Slope Max. Length Max. Rise Slope Max....
-
505.1 General
Handrails are not required on walking surfaces with running slopes less than 1:20....
-
Beveled: ADA Standard Section 303.3
Section 303.3 covers the current ADA Standards for beveled level changes.
-
1017.10 Trailhead Signs
requires trail information signs at trailheads to include information on the length of the trail or trail segment; surface type; typical and minimum tread width; typical and maximum running slope...
-
11B-411.2.1.3.4 Position
The face of individual elements or group of individual elements that are operated by user input shall slope away from the user at 15 to 25 degrees from the vertical plane. ...
-
1134A.6, Item 5
When a threshold is used, it shall be a maximum of 2 inches (50.8 mm) in height and have a beveled or sloped angle not exceeding 1 unit vertical in 2 units horizontal (26.6 degrees from...
-
Transits and construction lasers
Transits and construction lasers are useful for setting or measuring overall elevation points to determine a total slope....
-
Original research for ANSI A117.1 (1957 - 1961)
Both slope and cross slope were measured. These guidelines for measurement were deleted from later versions of the standard....
-
1134A.6, Item 5
When a threshold is used, it shall be a maximum of 2 inches (50.8 mm) in height and have a beveled or sloped angle not exceeding 1 unit vertical in 2 units horizontal (26.6 degrees from...
-
11B-809.10.6.5 Thresholds
Where provided thresholds shall be 2 inches (51 mm) maximum in height and have a beveled or sloped angle not exceeding 1 unit vertical in 2 units horizontal (26.6 degrees from the horizontal...
-
Wading pools. (Section-by-Section Analysis)
Section 242.3 of the 2004 ADAAG provides that newly constructed or altered wading pools must provide at least one sloped means of entry to the deepest part of the pool. ...