Alarm systems required to be accessible by 4.1 shall comply with 4.28.
Search Results "Fire-Building Surface"
-
4.28.1 GENERAL
-
A4.28.3 VISUAL ALARMS
The specifications in this section do not preclude the use of zoned or coded alarm systems. In zoned systems, the emergency exit lights in an area will flash whenever an audible...
-
1.1.3 Scope
this code shall apply to the construction, alteration, movement, enlargement, replacement, repair, equipment, use and occupancy, location, maintenance, removal and demolition of every building...
-
1009.12 Alarms/emergency warning systems/accessibility
Emergency warning systems as part of the fire alarm system shall be designed and installed in accordance with NFPA 72 as amended in Chapter 35....
-
1009.12 Alarms/emergency warning systems/accessibility
Emergency warning systems as part of the fire-alarm system shall be designed and installed in accordance with NFPA 72 as amended in Chapter 35....
-
1014.3 Floor
This section requires the floor surface within camp shelters to be firm and stable and to slope not steeper than 1:48 in any direction....
-
Installation of Test Surfaces
Installation of Test Surfaces In accordance with standard EWF design and construction practice (Figure 2), the full depth surfaces were prepared to the same requirements needed for permanent...
-
Installation of Aggregate Surfaces at Bradford Woods
Installation of Aggregate Surfaces at Bradford Woods The installation of the aggregate surfaces at Bradford Woods conformed to the following protocol: Prior to installing the crushed...
-
A4.5.1 GENERAL
Wheelchairs can be propelled most easily on surfaces that are hard, stable, and regular....
-
1007.12 Alarms/emergency warning systems/accessibility
Emergency warning systems as part of the fire alarm system shall be designed and installed in accordance with NFPA 72 as amended in Chapter 35....
-
Stabilizer Solutions StaLok Material Waterless Natural Pavement
Its unique surface characteristics resist weathering from water....
-
11B-305.2 Floor or ground surfaces
Floor or ground surfaces of a clear floor or ground space shall comply with Section 11B-302....
-
R302.7 Surfaces
R302.7 Surfaces....
-
M301.2 Transfer Surface (Section-by-Section Analysis)
This is an introductory section.
-
1.9.1 Division of the State Architect - Access Compliance.
Additions, alterations and structural repairs in all buildings and facilities shall comply with these provisions for new buildings, except as otherwise provided and specified herein....
-
1.9.1 Division of the State Architect - Access Compliance.
Additions, alterations and structural repairs in all buildings and facilities shall comply with these provisions for new buildings, except as otherwise provided and specified herein....
-
[2010 ADAS] 105.2.4 ICC/IBC
International Building Code, 2000 Edition (see 207.1, 207.2, 216.4.2, 216.4.3, and 1005.2.1). International Building Code, 2001 Supplement (see 207.1 and 207.2)....
-
Choice of Option One for Defining ‘‘Designed and Constructed for First Occupancy’’ (Preamble, Section-by-Section Analysis)
Option One for Defining ‘‘Designed and Constructed for First Occupancy’’ Under the option the Department has chosen for determining applicability of the new construction standards, a building...
-
Choice of Option One for Defining "Designed and Constructed for First Occupancy'' (Section-By-Section Analysis and Response to Comments)
First Occupancy'' (Section-By-Section Analysis and Response to Comments) Under the option the Department has chosen for determining applicability of the new construction standards, a building...
-
409.4.2 Floor Surfaces
Floor surfaces in elevator cars shall comply with 302 and 303....
-
409.4.2 Floor Surfaces
Floor surfaces in elevator cars shall comply with 302 and 303....
-
11B-306.2.3 Minimum required depth
The toe clearance shall extend 19 inches (483 mm) minimum under built-in dining and work surfaces required to be accessible by Section 11B-226.1....
-
11B-306.2.3 Minimum required depth
The toe clearance shall extend 19 inches (483 mm) minimum under built-in dining and work surfaces required to be accessible by Section 11B-226.1....
-
Rollability and Smoothness of Walking Surfaces
surfaces....
