Each 48 inch (1220 mm) minimum by 36 inch (915 mm) minimum area shall be oriented so that the 48 inch (1220 mm) minimum length is in the direction of the running slope of the curb ramp it...
Search Results "Segment Length"
Filters
Commonly Searched Documents
-
406.7 Islands
-
Floor Plan of Elevator Cars [4.10.9]
In alterations, smaller car sizes (minimum 47 inch width and 69 inch length) are permitted in cases of technical infeasibility, including where limited by existing shaft configurations (...
-
604.5.2 Rear Wall
The rear grab bar shall be permitted to be 24 inches (610 mm) long minimum, centered on the water closet, where wall space does not permit a length of 36 inches (915 mm) minimum due to the...
-
11B-411.2.3.1 Floor designation signs
The outside diameter of the star shall be 2 inches (51 mm) and all points shall be of equal length. Raised characters, including the star, shall be white on a black background....
-
11B-1003.2.2 Boarding piers at boat launch ramps
Where the total length of the gangway or series of gangways serving as part of a required accessible route is 30 feet (9144 mm) minimum, gangways shall not be required to comply with Section...
-
11B-1002.4.4.2 Side entry
For example, where a 42 inch (1065 mm) opening is provided, a minimum clear space of 60 inches (1525 mm) in length and 36 inches (915mm) in depth is needed to ensure adequate space for maneuvering...
-
11B-411.2.3.1 Floor designation signs
The outside diameter of the star shall be 2 inches (51 mm) and all points shall be of equal length. Raised characters, including the star, shall be white on a black background....
-
11B-1002.4.4.2 Side entry
For example, where a 42 inch (1065 mm) opening is provided, a minimum clear space of 60 inches (1525 mm) in length and 36 inches (915mm) in depth is needed to ensure adequate space for maneuvering...
-
Passenger Loading Zones
Accessible passenger loading zones must have an access aisle that is 60 inches wide minimum and extends the full length of the vehicle pull-up space....
-
5.4.1 Transfer Support Location for M301 and M302
Figure 5.4.1 Location and Length of Transfer Supports (SOURCE: Midmark Corporation) A: Table seat depth, 17 inches minimum B: Transfer support length, 15 inches minimum C: Distance...
-
Lift Compatibility (M301.4 and M302.4)
For example, full body bone densitometers usually have components that move beneath the length of the patient support surface and may prevent the equipment from meeting the technical criteria...
-
Effective communication and auxiliary aids.
Moreover, the number of individuals with hearing loss continues to grow in this country as a large segment of the population ages and as individuals live longer. ...
-
Section 37.75 Remanufacture of Non-Rail Vehicles and Purchase or Lease of Remanufactured Non-rail Vehicles by Public Entities Operating Fixed Route Systems
This exception applies to the remanufacture of or purchase of a remanufactured vehicle that (1) is of historic character; (2) operates solely on a segment of a fixed route system which is...
-
1. GENERAL
In general, worldwide, all facilities designed, constructed, altered, leased, or funded by DoD that are open to the public, or to limited segments of the public, or that may be visited by...
-
Landscape Forms Inc. Redline Bench Collection
3/4 inch cut steel Steel seat panel is laser cut and features perforations for heat release Seat panels are bolted to frame with stainless steel fasteners Available in 48" or 70" length...
-
11B-235.2 Boat slips
Because the number of boat slips is not demarcated, the total length of boat slip edge (55 feet, 17 m) must be used to determine the number of boat slips provided (two)....
-
11B-604.5 Grab bars
Reinforcement must be sufficient to permit the installation of rear and side wall grab bars that fully meet all accessibility requirements including, but not limited to, required length,...
-
Detectable Warnings
The Board has added clarification that detectable warnings be provided "along the full length of the public use area of the platform."...
-
Water Closet Location and Rear Grab Bar
The 1991 Standards contain no exception for grab bar length, and require the water closet centerline to be exactly 18 inches from the side wall, while the 2010 Standards requirement allows...
-
Parallel Parking Spaces (R309.2) (Section-by-Section Analysis)
Section-by-Section Analysis) Where the adjacent sidewalk or available right-of-way is more than 4.3 meters (14 feet) wide, an access aisle must be provided at street level for the entire length...
-
5.3.2.1 Transfer Sides Recommendation for Stretchers
This transfer location places the patient at a desirable location along the length of the stretcher side so that when the transfer is complete, the patient is in the proper location as the...
-
604.5.2 Rear Wall
The rear grab bar shall be permitted to be 24 inches (610 mm) long minimum, centered on the water closet, where wall space does not permit a length of 36 inches (915 mm) minimum due to the...
-
Platform Edges
Platform Edges The detectable warning must be placed at the platform edge and extend the full platform length in a 24 inch depth. This depth is an absolute dimension, not a minimum....
-
Obstructions [4.7.8]
A landing with a minimum length of 48 inches will provide sufficient turning space....
