These standing supports may be provided in a horizontal position, vertical position, or a combination of horizontal and vertical positions, as long as the minimum length of gripping surface...
Search Results "Vertical Reference Plane"
-
5.9 Standing Support Recommendations for M304 Diagnostic Equipment Used by Patients in a Standing Position
-
§104.33(b)(3)
(3) A recipient may place a handicapped person or refer such a person for aid, benefits, or services other than those that it operates or provides as its means of carrying out the requirements...
-
11B-411.2.1.4.1.1 Arrangement
Buttons shall be arranged in columns to the right of the keypad with a minimum horizontal spacing of 1.5 times the horizontal spacing between the numeric keys and with the same vertical...
-
11B-411.2.1.4.1.1 Arrangement
Buttons shall be arranged in columns to the right of the keypad with a minimum horizontal spacing of 1.5 times the horizontal spacing between the numeric keys and with the same vertical...
-
11B-411.2.1.4.1.1 Arrangement
Buttons shall be arranged in columns to the right of the keypad with a minimum horizontal spacing of 1.5 times the horizontal spacing between the numeric keys and with the same vertical...
-
1013.3 Height
Required guards shall not be less than 42 inches (1067 mm) high, measured vertically as follows: 1. From the adjacent walking surfaces; 2. ...
-
1015.3 Height
Required guards shall not be less than 42 inches (1067 mm) high, measured vertically as follows: From the adjacent walking surfaces....
-
R104.2 MUTCD
The portions of the Manual on Uniform Traffic Control Devices for Streets and Highways (MUTCD), 2009 Edition, that are incorporated by reference in this document consist of definitions (...
-
Section 35.171 Acceptance of complaints. (Section-by-Section Analysis)
The language of the 1991 title II regulation only requires the agency to refer such a complaint to the Department, which in turn refers the complaint to the appropriate designated agency...
-
E. What are the General Requirements for Curb Ramps in the ADA Standards for Accessible Design?
. [§ 4.1.6(3)(a)(ii)] The rise is the vertical change measured from the low point at the base of the curb ramp to the high point at the other end where the sloped...
-
Accessible Route to Parking Garages
In the proposed rule, this requirement referred to "parking garages." Comments considered that term to be too narrow and recommended alternatives such as "parking facilities."...
-
Landscape Forms Inc. Petoskey Bench Collection
Refer to materials/colors link on this page to view standard selections. FSC® certified woods available....
-
11B-703.7.2.6.3 Unisex toilet and bathing facilities
The vertices of the triangle shall be located ¼ inch (6.4 mm) maximum from the edge of the circle....
-
11B-703.7.2.6.3 Unisex toilet and bathing facilities
The vertices of the triangle shall be located ¼ inch (6.4 mm) maximum from the edge of the circle....
-
2. Question: What is the minimum width needed for a level boarding railroad passenger station platform to meet the accessibility requirements of the Americans with Disabilities Act (ADA)?
For a level boarding island passenger platform with vertical pedestrian access (by elevator, stairs, escalators, etc.), the minimum width should be the width of the vertical access facility...
-
11B-602.5 Spout location
The spout shall be located 15 inches (381 mm) minimum from the vertical support and 5 inches (127 mm) maximum from the front edge of the unit, including bumpers....
-
602.5 Spout Location
The spout shall be located 15 inches (380 mm) minimum from the vertical support and 5 inches (125 mm) maximum from the front edge of the unit, including bumpers....
-
10.3.2(4)
(4) In light rail, rapid rail and commuter rail key stations, the platform or a portion thereof and the vehicle floor shall be coordinated so that the vertical difference, measured when...
-
Self-Closing Faucets
The proposed rule referred to these as "self-closing" faucets. Commenters indicated that "metering" is a descriptor that is more accurate and consistent with plumbing codes....
-
(11) the City's ongoing failure to adopt any written policy or procedure
Aside from a brief reference to the adequacy of the City's transition plan, the FAC does not specifically reference any of the above policies. Dkt. 294, ¶ 44....
-
Re: 11B-904.3.4 Identification sign
when displayed, this section refers to "heck out aisles" instead of check out aisles...
-
1132A.4.1 Thresholds
Thresholds shall comply with the following: Thresholds with a change in height of not more than ¼ inch (6.35 mm) may be vertical. ...
-
Section 36.208(b) Direct Threat (Section-by-Section Analysis)
Originally, the reference to auxiliary aids or services as a mitigating factor was part of § 36.208....
-
§100.201 Accessible route
A route that complies with the appropriate requirements of ICC/ANSI A117.1-2003 (incorporated by reference at §100.201a), ICC/ANSI A117.1-1998 (incorporated by reference at §100.201a), CABO...
