Elevator car and hoistway doors and gates shall be power operated and shall comply with ANSI/BHMA A156.19....
Search Results "Automatic Door"
Filters
Commonly Searched Documents
-
11B-409.3.1 Power operation
-
11B-409.3.1 Power operation
Elevator car and hoistway doors and gates shall be power operated and shall comply with ANSI/BHMA A156.19....
-
11B-409.3.1 Power operation
Elevator car and hoistway doors and gates shall be power operated and shall comply with ANSI/BHMA A156.19....
-
11B-604.8.1.1.3 Maneuvering space with end-opening door
In a wheelchair accessible compartment with a door located in the front wall or partition (facing the water closet), either in-swinging or out-swinging, a minimum 60 inches (1524 mm) wide...
-
707.4 Privacy
Automatic teller machines shall provide the opportunity for the same degree of privacy of input and output available to all individuals. Advisory 707.4 Privacy....
-
11B-206.5.3 Transient lodging facilities
In transient lodging facilities, entrances, doors, and doorways providing user passage into and within guest rooms that are not required to provide mobility features complying with Section...
-
Smooth Surface
Exceptions from this requirement are recognized for sliding doors (Exception 1), certain tempered glass doors without stiles (Exception 2), doors and gates that do not extend to within 10...
-
1132A.8 Hand-activated door hardware
Hand-activated door latching, locking and opening hardware shall be centered between 30 inches (762 mm) and 44 inches (1118 mm) above the floor....
-
1132A.8 Hand-activated door hardware
Hand-activated door latching, locking and opening hardware shall be centered between 30 inches (762 mm) and 44 inches (1118 mm) above the floor....
-
409.3.1 Power Operation
Elevator car and hoistway doors and gates shall be power operated and shall comply with ANSI/BHMA A156.19 (1997 or 2002 edition) (incorporated by reference, see "Referenced Standards" in...
-
409.3.1 Power Operation
Elevator car and hoistway doors and gates shall be power operated and shall comply with ANSI/BHMA A156.19 (1997 or 2002 edition) (incorporated by reference, see "Referenced Standards" in...
-
D4. Door Clearance
On the pull side of the door, is there at least 18 inches clearance provided to the side of the latch if the door is not automatic or power-operated?...
-
Door Clear Width
Door Clear Width Open the door 90 degrees, measure from the face of the door to the edge of the door stop....
-
4.1.2(7)
(7) Doors: (a) At each accessible entrance to a building or facility, at least one door shall comply with 4.13....
-
Besam SW100 Low Energy Swing Door Operator
-
703.4.2 Location
Where a tactile sign is provided at a door, the sign shall be located alongside the door at the latch side....
-
Wikk Industries Inc. Bollard With Push Plate PART#BPRT126SMFT32D (630)
12”x6”x42” Tall, 7ga. Formed 304 Satin Stainless Steel US32D (630), Surface mount with concealed mounting base, 1 prep for INGRESS’R ® ADA switch (630), Welded Flat top. Shown on...
-
BEA Inc. LPR36 Series 36" Low Profile Push Plate
The LPR36 maximizes accessibility and independence for people with disabilities. The entire surface is “all-active” with four redundant membrane switches for consistent coverage. The...
-
Wikk Industries Inc. PART# BPS SM-ING48 DB (710) with I36-3 Clear (628)
6”X6”X48” Tall, Dark Bronze Anodized Aluminum (710), Surface mount with concealed mounting base, 2 Preps for INGRESS’R® and card reader, Removable Black ABS Cap. **Customer can...
-
Wikk Industries Inc. PART#BPS SM-INGR CLEAR (628) with I36-3 CLEAR (628)
6”X6”X42” Tall, Clear Anodized Aluminum (628), Surface mount with concealed mounting base, 1 prep for INGRESS’R® ADA switch, Removable Black ABS cap Shown on the bollard- I36-3...
-
Technical Memorandum TM 2017-25 Door and Gate Surfaces
TAS 404.2.10 also includes Exceptions for (1) sliding doors, (2) tempered glass doors (3) doors and gates which do not extend to within 10 inches of the finish floor, and (4) existing doors...
-
Entrances
space beyond the latch side of the door....
-
220 and 707 Automatic Teller Machines and Fare Machines
220 and 707 Automatic Teller Machines and Fare Machines Section 707 of the 2010 Standards adds specific technical requirements for speech output, privacy, tactilely-discernible input...
-
Are spring hinges and gravity hinges considered “closers” in determining the size of maneuvering clearances?
Some approaches require additional maneuvering clearances when a door or gate is equipped with a closer because of the additional force that must be counteracted in proceeding through doors...
