To provide adequate knee and leg clearance, desks and writing tables need to have at least 30 inches of knee width, 29 inches of knee height, and 19 inches of leg depth....
Search Results "Tread Depth"
-
1. Desk size
-
3(2)
Openings more than 24 inches in depth are not considered doorways. (See Fig. 1(d).)...
-
AccessRec DuraDeck 2 Molded Plastic Mat Ground Surface
Each DuraDeck panel has a unique integrated tread pattern molded onto sides, providing traction and stability for nearly any type of equipment, cranes, vehicles, and pedestrians....
-
Wading Pools
Wading Pools A wading pool is a pool designed for shallow depth and is used for wading. Each wading pool must provide at least one sloped entry into the deepest part....
-
Meeting the Challenge, Inc.
Through information dissemination, training, and direct technical assistance and in depth consulting service, we have pursued this focus for over 24 years....
-
M302.2 Transfer Surface
Transfer Surface M302.2.3 Transfer Sides Proposed requirement: The transfer surface shall be located to provide options to transfer from a mobility device onto one short side (depth...
-
M303.2.4 Knee and Toe Clearance
The depth of the wheelchair space shall include knee and toe clearance of 17 inches (430 mm) minimum and 25 inches (635 mm) maximum....
-
C. M303 Diagnostic Equipment Used by Patients Seated in a Wheelchair
significant changes to accommodate the unique challenges of mammography equipment; one significant change to the ramped running slope requirement; and a final significant change to the width and depth...
-
Transfer Surface Size – M301.2.2 Supine, Prone, or Side-Lying Position
Transfer Surface Size – M301.2.2 Supine, Prone, or Side-Lying Position The issues were discussed and decided in the full committee meeting as follows: depth of 17 inches minimum and width...
-
4.34.6.5(7)
The knee space shall have a clear width of 30 in (760 mm) and a clear depth of 19 in (485 mm)....
-
5.4.2 Transfer Support Length for M301 and M302
The transfer support would extend horizontally the entire depth of the transfer surface and would be 15 inches minimum in length....
-
Clear space
To calculate the space, three points were recorded for transfers to and from the platform: a point to the right of center, a point to the left of center, and a depth value (Figure 2)....
-
4.4 Knee and Toe Clearances
Knee Clearance Height (KCH) 685 640-650 680 700 Knee Clearance Depth (KCDL) 280...
-
Turning Space: ADA Standard Section 809.2.2
EXCEPTION: Turning space shall not be required in exterior spaces 30 inches (760 mm) maximum in depth or width. Advisory 809.2.2 Turning Space....
-
Trailhead Signs
trails designed for use by hikers or pedestrians, the final rule requires the signs to include information on the length of the trail or trail segment; surface type; typical and minimum tread...
-
Seating [4.32.2] and Knee Clearance [4.32.3]
Seating [4.32.2] and Knee Clearance [4.32.3] Knee space at least 27 inches high is required for a depth of 19 inches....
-
4.34.6.4(4)
The knee space shall have a minimum clear width of 30 in (760 mm) and a minimum clear depth of 19 in (485 mm)....
-
Step 3: Apply the Accessibility Provisions
This step involves looking at FSTAG, sections 7.4.1 through 7.4.8, which contain the technical requirements for trail grade, cross slope, resting interval, surface, clear tread width, passing...
-
Exemptions for Entire Trail or Beach Access Route
requirements for trails when: The combination of running slope and cross slope exceeds 40 percent for over 20 feet; A trail obstacle 30 inches high or more runs across the full tread...
-
5.4.1.2 Transfer and Positioning Support Location Recommendations for Imaging Equipment with Transfer Surfaces
of less than or equal to 24 inches and positioning supports for transfer depths greater than 24 inches....
-
11B-306.3.4 Clearance reduction
Between 9 inches (229 mm) and 27 inches (686 mm) above the finish floor or ground, the knee clearance shall be permitted to reduce at a rate of 1 inch (25 mm) in depth for each 6 inches...
-
407.8.3.2.1 Operable Part Height for ICT with Obstructed Forward Reach
Table 407.8.3.2.1 Operable Part Height for ICT with Obstructed Forward Reach Reach Depth Operable Part Height Less than 20 inches (510 mm) 48 inches...
-
Clear Floor Space [4.27.2]
controls, dispensers, receptacles, and other operable equipment as specified in 4.2; those recessed within niches or alcoves may require additional maneuvering space depending on the recess depth...
-
4.21.3 SEAT
The seat shall be mounted 17 in to 19 in (430 mm to 485 mm) from the bathroom floor and shall extend the full depth of the stall. The seat shall be on the wall opposite the controls....
