While the dynamic coefficient of friction during walking varies in a complex and non-uniform way, the static coefficient of friction, which can be measured in several ways, provides a close...
Search Results "Tape Measure"
-
I. Slip Resistant Surface—Aisles, Steps, Floor Areas Where People Walk, Floor Areas in Securement Locations, Lift Platforms, Ramps
-
5.1.2 Transfer Surface High Height
The transfer surface should have an adjustable height range with an upper height measuring at least 25 inches....
-
Technical Requirements
Technical Requirements—Specific numbers, conditions, and measurements that are required to be achieved (percent that must comply, dimensions, reach ranges, grades, trail width, etc.)....
-
4.34.5.2(2)
(2) The height of the water closet shall be at least 15 in (380 mm), and no more than 19 in (485 mm), measured to the top of the toilet seat....
-
§ 37.155(a)(1)
(1) Effects on current fixed route service, including reallocation of accessible fixed route vehicles and potential reduction in service, measured by service miles;...
-
Choosing the Right ecommerce seo company for Growth
This ensures that optimization efforts deliver measurable results. Another key factor is continuous improvement....
-
Seating Locations
Remember, when measuring the accessible route through the space, measure the aisle width as if the chairs are pulled out and occupied....
-
11B-608.2.2 Standard roll-in type shower compartments
Standard roll-in type shower compartments shall be 30 inches (762 mm) wide minimum by 60 inches (1524 mm) deep minimum clear inside dimensions measured at center points of opposing sides...
-
M304.2.1 Slip Resistant (Section-by-Section Analysis)
One manufacturer commented on this requirement, requesting that the rule provide clarification on how to define or measure a standing surface as “slip resistant.”...
-
1012.2 Height
Guards shall form a protective barrier not less than 42 inches (1067 mm) high, measured vertically above the leading edge of the tread, adjacent walking surface or adjacent seatboard....
-
E102.8 TIA (Section-by-Section Analysis)
TIA 1083 (2007), Telephone Terminal Equipment Handset Magnetic Measurement Procedures and Performance Requirements, would be incorporated by reference at 410.4.2....
-
C102.3 American National Standards Institute/ Institute of Electrical and Electronics Engineers (ANSI/IEEE)
ANSI/IEEE C63.19-2011 American National Standard for Methods of Measurement of Compatibility between Wireless Communications Devices and Hearing Aids, Committee C63 – Electromagnetic Compatibility...
-
10.2.1(1)
new bus stop pads are constructed at bus stops, bays or other areas where a lift or ramp is to be deployed, they shall have a firm, stable surface; a minimum clear length of 96 inches (measured...
-
E102.3 American National Standards Institute/ Institute of Electrical and Electronics Engineers (ANSI/IEEE)
ANSI/IEEE C63.19-2011 American National Standard for Methods of Measurement of Compatibility between Wireless Communications Devices and Hearing Aids, Committee C63 – Electromagnetic Compatibility...
-
4. Summary of Practice
4.1 This practice was developed specifically for estimating pathway roughness from longitudinal profile measurements. 4.2 Longitudinal profile measurements for one wheel track are transformed...
-
11B-608.2.2 Standard roll-in type shower compartments
Standard roll-in type shower compartments shall be 30 inches (762 mm) wide minimum by 60 inches (1524 mm) deep minimum clear inside dimensions measured at center points of opposing sides...
-
11B-604.7 Dispensers and disposal units
Toilet paper dispensers shall comply with 309.4 and shall be 7 inches (180 mm) minimum and 9 inches (230 mm) maximum in front of the water closet measured to the centerline of the dispenser...
-
11B-411.2.1.2.3 Accessibility function button
The dots shall be spaced ¼ inch (6.4 mm), measured center to center, in the form of an equilateral triangle with a vertex pointing up....
-
11B-411.2.1.2.3 Accessibility function button
The dots shall be spaced ¼ inch (6.4 mm), measured center to center, in the form of an equilateral triangle with a vertex pointing up....
-
11B-604.7 Dispensers and disposal units
Toilet paper dispensers shall comply with 309.4 and shall be 7 inches (180 mm) minimum and 9 inches (230 mm) maximum in front of the water closet measured to the centerline of the dispenser...
-
11B-411.2.1.2.5 Audio output
Auditory volume shall be at least 10 dB above ambient sound level, but shall not exceed 80 dB, measured 36 inches (914 mm) in front of the console....
-
11B-411.2.1.2.5 Audio output
Auditory volume shall be at least 10 dB above ambient sound level, but shall not exceed 80 dB, measured 36 inches (914 mm) in front of the console....