Specifically, the Department requested comment on the effectiveness of: annual surveys to assess the number of projects developed with accessible buildings; recordkeeping requirements; and...
Search Results "Horizontal Projection"
-
Enforcement Mechanisms
-
F248.1 General
administers or manages a beach constructs or alters circulation paths, parking facilities, toilet facilities, or bathing facilities to serve the beach or undertakes a beach nourishment project...
-
Online Course
It provides an overview of the project, three modules on the findings, implications for design and a link to resources like the reference list of publications derived from the project, the...
-
2.1 Path of Travel Elements
2.1 Path of Travel Elements: Under the CBC, certain alteration, addition and structural repair projects trigger requirements for upgrades to accessibility elements outside the project’s...
-
5.3.1 Permitted Obstructions to Transfer Sides for M301 and M302
NPRM Preamble Discussion: The Access Board is considering whether the final standards should permit equipment parts to extend horizontally 3 inches maximum beyond the edge of the transfer...
-
2. New Construction and Alterations
Since June 22, 1998, the City has required that all projects involving new construction or alterations of a building funded, in whole or in part, by the City, undergo review by City staff...
-
Bobrick ClassicSeries Surface-Mounted Soap Dispenser B-2112
Horizontal tank is satin-finish stainless steel. Valve dispenses all-purpose hand soaps. Capacity: 40‑fl oz (1.2‑L). Soap refill window. Concealed wall fastening....
-
11B-201.1 Scope, 11B-201.2 Application based on building or facility use, 11B-202.2 Additions, 11B-202.3 Alterations
Each altered element or space is relevant to projects occurring within the confines of a space(s) or room(s), or projects not occurring within the confines of a space(s) or room(s) as described...
-
Diaper Deck Infant Changing Table
Horizontal design only allows the baby to roll towards the wall and the parent greatly reducing your liability. ...
-
1133A.2.1 Clear width
Kitchens shall have a minimum clear width measured between any cabinet, countertop or the face of any appliance (excluding handles and controls) that projects into the kitchen and the opposing...
-
1133A.2.1 Clear width
Kitchens shall have a minimum clear width measured between any cabinet, countertop or the face of any appliance (excluding handles and controls) that projects into the kitchen and the opposing...
-
11B-809.10.5.2 Reinforcement for grab bars
Grab bar backing shall be installed horizontally to permit the installation of a 48-inch (1219 mm) grab bar with each end 6 inches (152 mm) maximum from the end walls of the bathtub....
-
11B-809.10.5.2 Reinforcement for grab bars
Grab bar backing shall be installed horizontally to permit the installation of a 48-inch (1219 mm) grab bar with each end 6 inches (152 mm) maximum from the end walls of the bathtub....
-
F216.4.1 Exit Doors
An exit passageway is a horizontal exit component that is separated from the interior spaces of the building by fire-resistance-rated construction and that leads to the exit discharge or...
-
216.4.1 Exit Doors
An exit passageway is a horizontal exit component that is separated from the interior spaces of the building by fire-resistance-rated construction and that leads to the exit discharge or...
-
Running Slope
This may be expressed as the percentage of change in elevation (grade) or as a ratio of vertical distance to horizontal distance (running slope)....
-
4.1.7(3)(e)
Exhibits and signage displayed horizontally (e.g., open books), should be no higher than 44 in (1120 mm) above the floor surface....
-
1009.6.4 Separation
Each area of refuge shall be separated from the remainder of the story by a smoke barrier complying with Section 709 or a horizontal exit complying with Section 1026....
-
§ 38.159(b)(10) Platform movement
The maximum platform horizontal and vertical acceleration when occupied shall be 0.3g....
-
3. Buttock-Popliteal Length
Buttock-Popliteal Length For this study, an estimate of buttock-popliteal length was calculated as the horizontal distance from the proximal (rear) edge of the wheelchair seat cushion...
-
404.2.10 Door and Gate Surfaces
Parts creating horizontal or vertical joints in these surfaces shall be within 1/16 inch (1.6 mm) of the same plane as the other. Cavities created by added kick plates shall be capped....
-
M305.2 Transfer Supports
M305.2 Transfer Supports M305.2.2 Transfer Supports Structural Strength Proposed requirement: Transfer supports and their connections shall be capable of resisting vertical and horizontal...
-
711.3.2 Membrane penetrations
By a horizontal distance of not less than 24 inches (610 mm); 1.2....
-
404.2.10 Door and Gate Surfaces
Parts creating horizontal or vertical joints in these surfaces shall be within 1/16 inch (1.6 mm) of the same plane as the other....
