โข Entrances and aisles with adequate head clearance and minimal projections into the path of travel result in easier navigation for people with lessened visual acuity or those who may be...
Search Results "Horizontal Projection"
Filters
Commonly Searched Documents
-
Vertical clearance and protruding objects
-
T503.1 General
Lights shall be shielded so as not to project directly into the eyes of entering and exiting passengers....
-
Beach Nourishment
An entity is not required to expend more than 20% of the costs of a beach nourishment project to provide a beach access route....
-
Non-Circular Cross Section and Clearance (ยง505.5, ยง505.7)
Non-Circular Cross Section and Clearance Recommendation:ย Projecting objects above handrails can impact their usability....
-
3. Buttock-Popliteal Length
Buttock-Popliteal Length For this study, an estimate of buttock-popliteal length was calculated as the horizontal distance from the proximal (rear) edge of the wheelchair seat cushion...
-
404.2.10 Door and Gate Surfaces
Parts creating horizontal or vertical joints in these surfaces shall be within 1/16 inch (1.6 mm) of the same plane as the other. Cavities created by added kick plates shall be capped....
-
M305.2 Transfer Supports
M305.2 Transfer Supports M305.2.2 Transfer Supports Structural Strength Proposed requirement: Transfer supports and their connections shall be capable of resisting vertical and horizontal...
-
711.3.2 Membrane penetrations
By a horizontal distance of not less than 24 inches (610 mm); 1.2....
-
404.2.10 Door and Gate Surfaces
Parts creating horizontal or vertical joints in these surfaces shall be within 1/16 inch (1.6 mm) of the same plane as the other....
-
Transfer Supports (M301.3.1, M302.3.1, and M305.2)
M305.2.2 would require the transfer supports and their connections to be capable of resisting vertical and horizontal forces of 250 pounds applied to all points of the transfer support....
-
11B-903.4 Back support
Back support shall be 2ยฝ inches (64 mm) maximum from the rear edge of the seat measured horizontally. [2010 ADAS] 903.4 Back Support....
-
11B-903.4 Back support
Back support shall be 2ยฝ inches (64 mm) maximum from the rear edge of the seat measured horizontally. [2010 ADA Standards] 903.4 Back Support....
-
Hager Companies Push/Pull Latch 311L
Hager Push/Pull Latch 311L: - Engraving available (optional) - Lead lined - Non-handed - Hospital Latch - 311L is same as 311H but for use on lead lined doors - *Horizontal...
-
F216.4.1 Exit Doors
An exit passageway is a horizontal exit component that is separated from the interior spaces of the building by fire-resistance-rated construction and that leads to the exit discharge or...
-
216.4.1 Exit Doors
An exit passageway is a horizontal exit component that is separated from the interior spaces of the building by fire-resistance-rated construction and that leads to the exit discharge or...
-
Running Slope
This may be expressed as the percentage of change in elevation (grade) or as a ratio of vertical distance to horizontal distance (running slope)....
-
4.1.7(3)(e)
Exhibits and signage displayed horizontally (e.g., open books), should be no higher than 44 in (1120 mm) above the floor surface....
-
1009.6.4 Separation
Each area of refuge shall be separated from the remainder of the story by a smoke barrier complying with Section 709 or a horizontal exit complying with Section 1026....
-
ยง 38.159(b)(10) Platform movement
The maximum platform horizontal and vertical acceleration when occupied shall be 0.3g....
-
Accessibility - Flatness and Lippage
Project specifications should make clear which trade is responsible for the required alterations if the subfloor is found not to be in compliance with the flatness requirements....
-
surface mounted toilet paper dispensers
Surface mounted dispensers are now being used for design and construction convenience, and they appear to pose an unnecessary hazard of injury due to the amount they project from the wall...
-
RECOMMENDATIONS
FEATURE AASHTO DESIGN VALUE (FOR BICYCLISTS) POTENTIAL DESIGN USER PERFORMANCE VALUE (85TH PERCENTILE) Sweep width 1.2 m Inline skaters 1.5 m Horizontal...
-
Call Button Clear Floor Space
...are all of the elevator lobbies free of ash trays or other elements placed below the elevator call buttons that project more than 4"?...
-
3. Sidewalk Width
3. ...is the usable width of sidewalks at least 36" wide to accommodate wheelchair travel, even if cars project over the curb onto the sidewalk?...
