The photo below shows that you measure horizontally from the face of the door in its 90 degree open position to the surface of the door stop on the frame opposite the hinge....
Search Results "Horizontal Projection"
-
B. Measuring Clear Passage at Doors
-
10.3.1(5)
on the side opposite from boarding) each shall have the top of the highest letter or symbol below the top of the vehicle window and the bottom of the lowest letter or symbol above the horizontal...
-
§ 38.83(b)(7) Platform gaps
When the lift is at vehicle floor height with the inner barrier (if applicable) down or retracted, gaps between the forward lift platform edge and vehicle floor shall not exceed 1/2 inch horizontally...
-
§ 38.23(b)(7) Platform gaps
platform is at vehicle floor height with the inner barrier (if applicable) down or retracted, gaps between the forward lift platform edge and the vehicle floor shall not exceed 1/2 inch horizontally...
-
R410.6 Character Height
Viewing distance shall be measured as the horizontal distance between the character and an obstruction preventing further approach towards the sign....
-
A. Measuring Slope and Cross Slope
While holding the uphill end of the level on the pavement, place the pencil under the other end and roll it toward the uphill end of the level until the horizontal air bubble in the center...
-
11B-406.5.1 Location
Curb ramps and the flared sides of curb ramps shall be located so that they do not project into vehicular traffic lanes, parking spaces, or parking access aisles....
-
4.1.3(2) ENTRANCES
EXCEPTION: In projects consisting of one-to-four family dwellings where accessible entrances would be extraordinarily costly due to site conditions or local code restrictions, accessible...
-
Additions [§202.2]
Additions [§202.2] Projects that increase, expand, or extend a facility’s gross floor area or height of a facility are considered additions (as defined in §106.5) and must comply with...
-
Protruding Objects [§204]
Protruding Objects [§204] To prevent hazards to people with vision impairments, the standards limit the projection of objects into circulation paths....
-
68.102(a) Compliance with the Proposed Accessibility Guidelines for Pedestrian Facilities in the Public Right-of-Way
(a) For public right-of-way projects, in addition to accepting compliance with applicable TAS requirements, the department will also accept compliance with the Proposed Accessibility Guidelines...
-
11B-406.5.1 Location
Curb ramps and the flared sides of curb ramps shall be located so that they do not project into vehicular traffic lanes, parking spaces, or parking access aisles....
-
11B-406.5.1 Location
Curb ramps and the flared sides of curb ramps shall be located so that they do not project into vehicular traffic lanes, parking spaces, or parking access aisles....
-
Accessible Gates for Trails and Roads
United States Department of Agriculture Forest Service Technology & Development Program October 2006 For additional information, contact: Scott Groenier, project leader...
-
7. APPLICABILITY
All projects in or after Fiscal Year 2010, regardless of the source of funds, must be programmed, designed, and constructed to comply with these DoD Standards....
-
Conclusion
The resources in Appendix C include projects and collaborative efforts that address physical activity among people with disabilities....
-
Interactive Illuminated Models
Interactive Illuminated Models Another promising new development expands on the concept of touch sensitive talking models by projecting light onto the model’s 3D surface....
-
68.54. Review and Inspection of Buildings and Facilities with an Estimated Construction Cost of Less than $50,000 or Not Subject to the Act
(New rule section effective March 1, 2007, 32 TexReg 884) (a) When construction documents for projects with an estimated construction cost of less than $50,000 are mailed, shipped or...
-
11B-404.2.4.3 Recessed doors and gates
approach shall be provided when any obstruction within 18 inches (457 mm) of the latch side at an interior doorway, or within 24 inches (610 mm) of the latch side of an exterior doorway, projects...
-
11B-404.2.4.3 Recessed doors and gates
approach shall be provided when any obstruction within 18 inches (457 mm) of the latch side at an interior doorway, or within 24 inches (610 mm) of the latch side of an exterior doorway, projects...
-
Alterations [§202.3]
Many types of projects are covered as “alterations,” including remodeling, renovation, rehabilitation, reconstruction, restoration, resurfacing of circulation paths or vehicular ways, and...
-
14. Access and Construction Database
in Section 17 below; (f) the amount of Annual Commitment funds expended during the prior two (2) City fiscal years (with a breakdown of the amounts expended for general categories of projects...
-
Compliance Problems Due to Lack of Accessibility Guidelines
Two commenters requested that interim accessibility guidelines should be adopted for projects "caught in the middle", i.e. those projects started before publication of the final Guidelines...
-
Section 36.303(g)(7) Compliance Date for Providing Captioning and Audio Description
The Department also proposed to give movie theaters that converted their auditoriums with analog projection systems to digital projection systems after the publication date of the rule an...