This revision to provide options for two types of transfer surfaces necessitated adding additional technical criteria addressing transfer surface size (M301.2.3) and transfer supports (M305.2...
Search Results "Vertical Standing Support"
Commonly Searched Documents
-
(1) Transfer Surface Location for Diagnostic Equipment Used in the Supine, Prone, or Side-lying Position
-
Section A: Parking
, 502.3) Width of space _____ Width of access aisle _____ A3 For van accessible spaces (particularly in a garage or parking structure), is there vertical...
- Mayer-Rothschild Foundation: Determination of Grab Bar Specifications for Independent and Assisted Transfers in Residential Care Settings
-
C. ARTICLE III STANDING
ARTICLE III STANDING 43....
-
M305.2.4.1 Circular Cross Section
Transfer supports with circular cross sections shall have an outside diameter of 1 ¼ inches (32 mm) minimum and 2 inches (51 mm) maximum....
-
Components of Accessible Routes
[See subsections ...]
-
11B-303.2 Vertical
Changes in level of ¼ inch (6.4 mm) high maximum shall be permitted to be vertical and without edge treatment. [2010 ADAS] 303.2 Vertical. ...
- Hoyer Journey Stand-Up Lift
-
Interior Routes
Exposed edges securely fastened with trim on exposed edge. 11B-302.2 Vertical clearances/protrusions along circulation paths. 11B-307...
-
Interior Routes
Exposed edges securely fastened with trim on exposed edge. 11B-302.2 Vertical clearances/protrusions along circulation paths. 11B-307...
-
Examples of access:
Exam table that lowers to 17-19 inches from the floor Many people find these tables easier to use. There are many ways to help people get access. See the [images]...
-
ADA Requirements - Service Animals
U.S. Department of Justice Civil Rights Division Disability Rights Section Service Animals The Department of Justice published revised final regulations implementing the...
-
11B.707.7.1.1 Vertically mounted display screen
Where display screens are mounted vertically or tipped away from the viewer less than 30 degrees, the center line of the display screen and other display devices shall be no more than 52...
-
11B-703.7.2.6.4 Edges and vertices on geometric symbols
Vertices shall be radiused between 1/8 inch (3.2 mm) minimum and ¼ inch (6.4 mm) maximum....
-
11B-303.2 Vertical
Changes in level of ¼ inch (6.4 mm) high maximum shall be permitted to be vertical and without edge treatment. [2010 ADAS] 303.2 Vertical. ...
-
11B-303.2 Vertical
Changes in level of ¼ inch (6.4 mm) high maximum shall be permitted to be vertical and without edge treatment. [2010 ADA Standards] 303.2 Vertical....
-
Vertical Surface Discontinuities
Vertical Surface Discontinuities. Vertical differences in level between two adjacent surfaces....
-
M305.2.4.2 Non-Circular Cross Section
Transfer supports with non-circular cross sections shall have a cross-section dimension of 2 inches (51 mm) maximum and a perimeter dimension of 4 inches (100 mm) minimum and 4.8 inches...
- Comfort Designs Comfort Care™ Grab Bars
-
§ 35.151(g) Assembly areas
(g) Assembly areas. Assembly areas subject to the proposed standards shall comply with the provisions applicable to assembly areas, including, but not limited to, sections 221 and...
-
§ 35.151(g) Assembly areas.
(g) Assembly areas. Assembly areas subject to this section shall comply with the provisions of the 2010 Standards applicable to assembly areas, including, but not limited to,...
-
Drinking Fountains for Standing Persons
Specifications for drinking fountains for standing persons address the height of the spout outlet (602.7)....
-
602.7 Drinking Fountains for Standing Persons
602.7 Drinking Fountains for Standing Persons....
-
Exam Tables and Chairs
A handle or support rail is often needed along one side of the table for stability during a transfer and during the examination....