You should use an accessible scale with people who… Have difficulty standing or maintaining balance on a standard scale platform....
Search Results "Vertical Standing Support"
Filters
Commonly Searched Documents
-
Tips for Weighing People Using an Accessible Scale
-
Mega Jailhouse Anti-Suicide Grab Bar with Closure Plate 18 inches - Concealed Mounting
Description: This 18" security / anti-suicide grab bar is fabricated in accordance with ADA specifications and is fully enclosed, thereby abating suicide risk. The grab bar is...
-
Section 35.151(g) Assembly areas (Section-by-Section Analysis)
The vertical viewing angle is the angle between a horizontal line perpendicular to the seated viewer's eye to the screen and a line from the seated viewer's eye to the top of the screen....
-
M101.2 Application (Section-by-Section Analysis)
In the NPRM the Access Board proposed that the MDE Standards would be applied to diagnostic equipment based on the patient position the equipment is designed to support....
-
11B-602.7 Drinking fountains for standing persons
Spout outlets of drinking fountains for standing persons shall be 38 inches (965 mm) minimum and 43 inches (1092 mm) maximum above the finish floor or ground....
-
Pressalit Care VALUE Support Arm Fixed Height Swing Grab Bar
Support arm Incl. fixing kit for brick wall Basic material: Steel Surface material: Rilsan End cap: Nylon (PA) Provides firm support when you are sitting, standing, or transferring...
-
M305.2.7 Clearance (Section-by-Section Analysis)
In the MDE NPRM, the Access Board did not provide any specific requirements for clearances around the transfer support....
-
Sec.36.308(a)(3)
(3) The requirements of paragraph (a) of this section shall not be interpreted to exceed the standards for alterations in subpart D of this part.
-
M305.2.8 Fittings (Section-by-Section Analysis)
The MDE NPRM proposed to require that transfer supports not rotate in their fittings (proposed M305.2.3). Five commenters addressed this provision....
-
M305.2.2 Length
The length of transfer supports shall comply with M305.2.2.1 or M305.2.2.2....
-
Pressalit Care VALUE Support Arm Fixed Height Swing Grab Bar with Leg
Support arm with leg, height 800 mm....
-
M305.2.3 Height (Section-by-Section Analysis)
The MDE Advisory Committee supported adding a requirement setting the height of transfer supports within the range described in question 20 in the MDE NPRM preamble, of 6 inches minimum...
-
M305.2.6 Gripping Surfaces (Section-by-Section Analysis)
The proposed rule did not provide any specific requirements regarding gripping surfaces on transfer supports....
-
M305.2.1 Location
Transfer supports shall comply with M305.2.1.1 or M305.2.1.2 and shall be located 1 ½ inches (38 mm) maximum measured horizontally from the plane defined by the nearest edge of the transfer...
-
Section 35.151(g) Assembly Areas (Section-by-Section Analysis)
following criteria: (i) it is located within the rear sixty percent (60%) of the seats provided in an auditorium; or (ii) it is located within the area of an auditorium in which the vertical...
-
M305.2.6 Gripping Surface
Transfer support gripping surfaces shall be continuous along their length and shall not be obstructed along their tops or sides....
-
M305.2.3 Fittings
Transfer supports shall not rotate within their fittings....
-
Murdock Manufacturing Grab Bars
Grab bars are designed to support a load of at least 250 pounds (113.4 kilogram) grab bars at 33 inch (83.82 cm) above floor or in accordance with local accessibilty regulations....
-
M305.2.4 Cross Section (Section-by-Section Analysis)
The proposed rule did not provide specific requirements for the cross section of transfer supports....
-
Bradley Grab Bars 1 1/2" with Concealed Mounting 812
Intermediate supports are contour cut and joined by welding to form an integral part of the grab bar. All exposed welds ground and polished to blend....
-
M305.2.8 Fittings
Transfer supports shall not rotate within their fittings when in place for transfer....
-
Vertical Alignment-Crest Vertical Curves
Vertical Alignment-Crest Vertical Curves A crest vertical curve is present when a shared use path (or a roadway) goes uphill and then goes downhill....
-
303.2 Vertical
303.2 Vertical. Changes in level of ¼ inch (6.4 mm) high maximum shall be permitted to be vertical. Figure 303.2 Vertical Change in Level...
-
M305.2.7 Clearance
Clearance between the transfer support gripping surface and adjacent surfaces or obstructions shall be 1 ½ inches (38 mm) minimum....
