(c) The following toilet facilities, whichever is greater: (i) At least one toilet facility for each sex in the altered building complying with 4.22, Toilet Rooms, and 4.23, Bathrooms...
Search Results "Fire-Building Surface"
-
4.1.6(3)(c)
-
11B-802.1.5 Overlap
The term "circulation paths" used in 802.1.5 means aisle width required by applicable building or life safety codes for the specific assembly occupancy....
-
1.1.10 Availability of codes
At least one complete copy each of Titles 8, 19, 20, 24, and 25 with all revisions shall be maintained in the office of the building official responsible for the administration and enforcement...
-
§ 37.9(c)(1)
(1) New construction or alterations of buildings or facilities on which construction has begun, or all approvals for final design have been received, before November 29, 2006, are not required...
-
1.1.10 Availability of codes
At least one complete copy each of Titles 8, 19, 20, 24, and 25 with all revisions shall be maintained in the office of the building official responsible for the administration and enforcement...
-
106.5.10 Assembly Area
A building or facility, or portion thereof, used for the purpose of entertainment, educational or civic gatherings, or similar purposes....
-
802.1.5 Overlap
The term "circulation paths" used in Section 802.1.5 means aisle width required by applicable building or life safety codes for the specific assembly occupancy....
-
802.1.5 Overlap
The term "circulation paths" used in 802.1.5 means aisle width required by applicable building or life safety codes for the specific assembly occupancy....
-
11B-404.2.7 Door and gate hardware
In addition to the requirements of this section, designers should be aware of the Part 12, Section 12-10-202(f) requirement for lever hardware as adopted by the State Fire Marshal. ...
-
1011.3 Operable Parts
Exception 1 requires fire rings, grills, fireplaces, wood stoves, water hydrants, and water utility hook-ups to comply with the technical requirements for operation in 309.4 of the Architectural...
-
11B-1002.6 Transfer devices for use with amusement rides
Where possible, designers are encouraged to locate the transfer device seat no higher than 17 to 19 inches (430 to 485 mm) above the load and unload surface....
-
1002.6 Transfer Devices for Use with Amusement Rides
Where possible, designers are encouraged to locate the transfer device seat no higher than 17 to 19 inches (430 to 485 mm) above the load and unload surface....
-
When Ramps Are Required
Rise of a ramp is the amount of vertical distance the inclined or slanted surface ascends or descends....
-
R210.3 Shared Use Paths
Objects shall not overhang or protrude into any portion of a shared use path at or below 2.4 m (8.0 ft) measured from the finish surface....
-
Alternative Golf Car Passage
While a golf car passage must be usable by golf cars, it does not necessarily need to have a prepared surface and may be part of a golf car path....
-
4. Wheelchair seat depth
The median seat depth across different wheeled mobility devices would provide a reference value for the depth of other common seating surfaces....
-
COSTS TO LOWER MINIMUM TABLE HEIGHT
The need to reach heights above 32 inches interferes with efforts to lower the transfer surface height....
-
Initial Measures and Transfer Setup
This approach is also widely promoted in rehabilitation research (A Clinical Application Guide to Standardized Wheelchair Seating Measurements of the Body and Seating Support Surfaces, See...
-
3. FIXTURES and HARDWARE
If self-closing valves are used, the faucet shall remain open for at least 10 seconds.”xxii Sinks Exposed Pipes and Surfaces: Hot water and drain pipes under lavatories...
-
Standardized Tests of Physical Fitness and Community Ambulation
The subjects rated the level of difficulty from 1 to 10 for both straight travel and turning on the surface using the Level of Difficulty Rating Scale....
-
Multiple Parking Facilities on a Site
., surface lot versus parking garage or deck); dedicated to, and separately serve, different facilities on a site; segmented and separated by guard rails, fencing, or barriers...
-
11B-1002.6 Transfer devices for use with amusement rides
Where possible, designers are encouraged to locate the transfer device seat no higher than 17 to 19 inches (430 to 485 mm) above the load and unload surface....
-
11B-1002.6 Transfer devices for use with amusement rides
Where possible, designers are encouraged to locate the transfer device seat no higher than 17 to 19 inches (430 to 485 mm) above the load and unload surface....
-
1002.6 Transfer Devices for Use with Amusement Rides
Where possible, designers are encouraged to locate the transfer device seat no higher than 17 to 19 inches (430 to 485 mm) above the load and unload surface....