Available Finish US26D and US10B stock finish, other finishes upon request Code Compliance: ANSI/BHMA Meets or exceeds all Grade 2 requirements of A156.2-2003 UL Listed 3-hour fire...
Search Results "Fire-Building Surface"
- TownSteel CSRC Series, Grade 2, Clutched, Conical Rose Cylindrical Locks
- TownSteel CB Series, Grade 2 Non-Clutched Flat Rose Cylindrical Locks
-
11B-703.7.2.7 Pedestrian traffic-control buttons
Control buttons shall be located no higher than 48 inches (1219 mm) above the ground surface adjacent to the pole....
-
11B-1009.5.4 Transfer steps
The surface of the bottom tread shall extend to a water depth of 18 inches (457 mm) minimum below the stationary water level. [2010 ADAS] Advisory 1009.5.4 Transfer Steps. ...
-
1016.6 Openings
Openings in the surface of outdoor recreation access routes shall not allow the passage of a sphere more than 1/2 inch (13 mm) in diameter. Advisory 1016.6 Openings. ...
-
Court Sports
Accessible routes must comply with all ADAAG requirements, such as width and changes in level or surface, and must directly connect both sides of the court....
-
703.6.2 Finish and Contrast
Additional factors affecting the ease with which the text can be distinguished from its background include shadows cast by lighting sources, surface glare, and the uniformity of the text...
-
703.6.2 Finish and Contrast
Additional factors affecting the ease with which the text can be distinguished from its background include shadows cast by lighting sources, surface glare, and the uniformity of the text...
-
1132A.4, Item 3
Secondary exterior doors onto decks, patios, or balcony surfaces constructed of impervious materials (e.g., concrete, brick, flagstone) may have a maximum change in height from the interior...
-
407.2 Contrast (Section-by-Section Analysis)
407.2 Contrast (Section-by-Section Analysis) This section proposes that keys and controls, where provided, contrast visually from background surfaces....
-
5.3.6 Entrance
The entrance to the toilet shall be level with the surrounding surface....
-
4.9.4(2)
At the top, the extension shall be parallel with the floor or ground surface....
-
5.3.6 Entrance
The entrance to the toilet shall be level with the surrounding surface....
-
1016.6 Openings
Openings in the surface of outdoor recreation access routes shall not allow the passage of a sphere more than 1/2 inch (13 mm) in diameter. Advisory 1016.6 Openings....
-
Error/Omission: Landing areas where ramps change direction (e.g., switchbacks or 90° turns) are too small.
Result: Wheelchair users are unable to go up or down the ramp because there is not enough space to turn on a level surface. This makes the ramp unusable....
-
11B-703.7.2.7 Pedestrian traffic-control buttons
Control buttons shall be located no higher than 48 inches (1219 mm) above the ground surface adjacent to the pole....
-
403.5.3 Passing Spaces
Passing spaces shall be either: a space 60 inches (1525 mm) minimum by 60 inches (1525 mm) minimum; or, an intersection of two walking surfaces providing a T-shaped space complying with...
-
1009.5.4 Transfer Steps
The surface of the bottom tread shall extend to a water depth of 18 inches (455 mm) minimum below the stationary water level. Advisory 1009.5.4 Transfer Steps....
-
403.5.1 Clear Width
Except as provided in 403.5.2 and 403.5.3, the clear width of walking surfaces shall be 36 inches (915 mm) minimum....
-
703.6.2 Finish and Contrast
Additional factors affecting the ease with which the text can be distinguished from its background include shadows cast by lighting sources, surface glare, and the uniformity of the text...
-
Kurt Knight: Development of VA Standards
We don’t use it in other types of functions that don’t change as rapidly as a clinic building or a bed building....
-
PLATFORM
A raised area within a building used for worship, the presentation of music, plays or other entertainment; the head table for special guests; the raised area for lecturers and speakers;...
-
11B-802.1.5 Overlap
The term "circulation paths" used in 802.1.5 means aisle width required by applicable building or life safety codes for the specific assembly occupancy....