When a condition for an exception prohibits full compliance with a specific technical requirement on a portion of a beach access route, that portion of the beach access route must still...
Search Results "Full Length Mirror"
Filters
Commonly Searched Documents
-
Exceptions to the Guidelines That Apply to Beach Access Routes
-
11B-505.6 Gripping surface
Handrail gripping surfaces shall be continuous along their length and shall not be obstructed along their tops or sides....
-
Section 37.139 Plan Contents
There is no document length requirement, however. Each entity (or group plan) is unique and we expect the plans to reflect this....
-
1133A.4, Item 2
A minimum linear length of 30 inches (762 mm) of countertop shall be provided for a work surface....
-
1133A.4, Item 2
A minimum linear length of 30 inches (762 mm) of countertop shall be provided for a work surface....
-
11B-812.7.2 Marking
Access aisle markings may extend beyond the minimum required length....
-
Bradley In-Wall Towel Dispenser 198
Satin finish Stainless Steel Towel dispenser For Installation Behind Wall or Mirror For 1/2" Thick Drywall Installation For 5/8" Thick Drywall, use...
-
Selection of Variables
Selection of Variables Our own review of the ADAAG requirements, plus that of our subcontractor KRW, reveals that the single most needed anthropometric datum, by far, is arm length....
-
Handrail Extensions: ADA Standard Section 505.10
Section 505.10 covers the current ADA Standards for handrail extensions.
-
11B-705.1.2.2.1 Perpendicular curb ramps
Detectable warnings shall extend the full width of the ramp run less 2 inches (51 mm) maximum on each side, excluding any flared sides....
-
11B-404.2.4 Maneuvering clearances
Maneuvering clearances shall extend the full width of the doorway and the required latch side or hinge side clearance. Exception: Reserved....
-
1133A.4, Item 1
A minimum linear length of 30 inches (762 mm) of countertop shall be provided for the kitchen sink installation....
-
1017.7 Slopes
This section contains technical requirements for the maximum running slope and segment length (1017.7.1) and cross slope (1017.7.2) of trails....
-
1133A.4, Item 1
A minimum linear length of 30 inches (762 mm) of countertop shall be provided for the kitchen sink installation....
-
Gamco Horizontal Wall-Mounted Baby Changing Station Cream - BCS-1
Reinforced full-length steel-on-steel hinge mechanism, with 11-gauge steel mounting plates and mounting hardware included....
-
Gamco Horizontal Wall-Mounted Baby Changing Station Grey - BCS-2
Reinforced full-length steel-on-steel hinge mechanism, with 11-gauge steel mounting plates and mounting hardware included....
-
Side Transfer Surface
A transfer surface located within the length of the examination surface that allows patient transfer on two opposing sides of the examination surface....
-
M305.2.1.1 End Transfer Supports
Transfer supports for transfer surfaces complying with M301.2.3.1 and M302.2 shall be located on the short side (length) opposite the transfer side....
-
6.8.1 Size
The resting interval length shall be a minimum of 60 inches (1525 mm) long by 60 inches (1525 mm) wide....
-
Just Manufacturing Classroom Deck Mount Lever Handle Faucet
ALL STAINLESS STEEL DECK MOUNT FAUCET- LEAD FREE COMPLIANT - ADA COMPLIANT POLISHED STAINLESS MIRROR FINISH....
-
Pilot Rock WPTS Square Frame Table Using Recycled Plastic
Full length seats offer full capacity seating which is an advantage over extended top or side access tables....
-
Pilot Rock WPTS Square Frame Table Using Lumber
Full length seats offer full capacity seating which is an advantage over extended top or side access tables....
-
11B-221.2.3.1 Horizontal dispersion
required in assembly areas with 300 or fewer seats if the companion seats required by Section 11B-221.3 and wheelchair spaces are located within the 2nd or 3rd quartile of the total row length...
-
505.6 Gripping Surface
Handrail gripping surfaces shall be continuous along their length and shall not be obstructed along their tops or sides....
