Handrail gripping surfaces with a circular cross section shall have an outside diameter of 1 1/4 inches (32 mm) minimum and 2 inches (51 mm) maximum....
Search Results "Ramp Surface"
Filters
Commonly Searched Documents
-
505.7.1 Circular Cross Section
-
505.7.1 Circular Cross Section
Handrail gripping surfaces with a circular cross section shall have an outside diameter of 1 1/4 inches (32 mm) minimum and 2 inches (51 mm) maximum....
-
505.7.1 Circular Cross Section
Handrail gripping surfaces with a circular cross section shall have an outside diameter of 1¼ inches (32 mm) minimum and 2 inches (51 mm) maximum....
-
Handrails
Handrails Handrails are required on both sides of ramps connecting elevated play components....
-
6e. Ramp Landing
Is a level landing, at least 60 inches by 60 inches, provided where a ramp changes direction? [ADA Stds 4.8.4] Yes _____ No _____...
-
11B-304.2 Floor or Ground Surfaces
Floor or ground surfaces of a turning space shall comply with Section 11B-302. Changes in level are not permitted. Exception: Slopes not steeper than 1:48 shall be permitted....
-
11B-304.2 Floor or Ground Surfaces
Floor or ground surfaces of a turning space shall comply with Section 11B-302. Changes in level are not permitted. Exception: Slopes not steeper than 1:48 shall be permitted....
-
1132A.9 Smooth surface
1132A.9 Smooth surface. ...
-
Perpendicular Curb Ramps (R304.2) (Section-by-Section Analysis)
Perpendicular Curb Ramps (R304.2) (Section-by-Section Analysis) Perpendicular curb ramps have a running slope that cuts through or is built up to the curb at right angles or meets the...
-
11B-304.2 Floor or ground surfaces
Floor or ground surfaces of a turning space shall comply with Section 11B-302. Changes in level, slopes exceeding 1:48, and detectable warnings shall not be permitted....
-
2.2 Surface
The surface of an ORAR shall be firm and stable. The type of surface should be appropriate to the setting and level of development....
-
Handrails Along Walking Surfaces [§403.6, §505]
Handrails Along Walking Surfaces [§403.6, §505] Handrails are required at ramps with a rise greater than 6” and at stairs that are part of a means of egress, but not at other locations...
-
11B-408.4.2 Floor surfaces
Floor surfaces in elevator cars shall comply with Sections 11B-302 and 11B-303....
-
302 Floor or Ground Surfaces
[See subsections ...]
-
302 Floor or Ground Surfaces
[See subsections ...]
-
A4.5 Ground and Floor Surfaces
[See subsections ...]
-
4.5 Ground and Floor Surfaces
[See subsections ...]
-
A4.5 GROUND AND FLOOR SURFACES.
[See subsections ...]
-
4.5 GROUND AND FLOOR SURFACES
[See subsections ...]
-
R404.2 Surfaces
R404.2 Surfaces....
-
Parallel Curb Ramps (R304.3) (Section-by-Section Analysis)
Parallel Curb Ramps (R304.3) (Section-by-Section Analysis) Parallel curb ramps have a running slope that is in-line with the direction of sidewalk travel and lower the sidewalk to a level...
-
11B-705.1.2.2.2.1 One entrance/exit point
Where the turning space has one entrance/exit point other than the sloped ramp segments, detectable warnings shall be 36 inches (914 mm) deep, as measured perpendicular to the curb, and...
-
Accessible Ramp Features
Accessible Ramp Features 1. At least 36 inches between handrails 2. Top landing part of walk 3. Bottom landing part of walk 4. Handrail height 34 to 38 inches 5....
-
1132A.9 Smooth surface
Swinging door or gate surfaces within 10 inches (254 mm) of the finish floor or ground measured vertically shall have a smooth surface on the push side extending the full width of the door...