There shall be no sharp or abrasive surfaces under the work surface counters....
Search Results "Ramp Surface"
-
11B-804.3.3 Exposed surfaces
-
11B-804.3.3 Exposed surfaces
There shall be no sharp or abrasive surfaces under the work surface counters....
-
11B-804.3.3 Exposed surfaces
There shall be no sharp or abrasive surfaces under the work surface counters....
-
Surface Slopes
The final rule requires clear ground spaces to have slopes not steeper than 1:48 in any direction and, where the surface is other than concrete, asphalt, or boards, permits slopes not steeper...
-
404.2.10 Door and Gate Surfaces
404.2.10 Door and Gate Surfaces....
-
RESULTS OF OBJECTIVE SURFACE MEASUREMENT
The work to negotiate a ramp was linearly related to the angle of the ramp....
-
302.1 Floor or Ground Surfaces
302.1 Floor or Ground Surfaces Both section 4.5.1 of the 1991 Standards and section 302.2 of the 2010 Standards require that floor or ground surfaces along accessible routes and in accessible...
-
11B-502.4 Floor or ground surfaces
[2010 ADAS] Advisory 502.4 Floor or Ground Surfaces. ...
-
11B-502.4 Floor or ground surfaces
[2010 ADAS] Advisory 502.4 Floor or Ground Surfaces. ...
-
404.2.10 Door and Gate Surfaces
Swinging door and gate surfaces within 10 inches (255 mm) of the finish floor or ground measured vertically shall have a smooth surface on the push side extending the full width of the door...
-
4.1.6 Surface
The surface of the clear floor or ground space shall be firm and stable. The type of surface should be appropriate to the setting and level of development. ...
-
11B-405.7.4 Change in direction
Ramps that change direction between runs at landings shall have a clear landing 60 inches (1525 mm) minimum by 72 inches (1829 mm) minimum in the direction of downward travel from the upper...
-
11B-405.7.4 Change in direction
Ramps that change direction between runs at landings shall have a clear landing 60 inches (1525 mm) minimum by 72 inches (1829 mm) minimum in the direction of downward travel from the upper...
-
404.2.10 Door and Gate Surfaces
Swinging door and gate surfaces within 10 inches (255 mm) of the finish floor or ground measured vertically shall have a smooth surface on the push side extending the full width of the door...
-
4.6.6 Surface
The surface of the clear floor or ground space required by section 4.6.4 shall be firm and stable. The type of surface should be appropriate to the setting and level of development. ...
-
1002.4.1 Floor or Ground Surface
1002.4.1 Floor or Ground Surface. The floor or ground surface of wheelchair spaces shall be stable and firm....
-
Envirobond Organic-Lock™ Surface Stabilizer
Important features of a surface stabilized with Organic-Lock™ include: Erosion Control - Organic-Lock stabilized surfaces offer significantly improved resistance to erosion over...
-
11B-705.1.2.2 Curb ramps
Detectable warnings at curb ramps shall comply with Section 11B-705.1.2.2....
-
802.1.1 Floor or Ground Surface
802.1.1 Floor or Ground Surface. The floor or ground surface of wheelchair spaces shall comply with 302. Changes in level are not permitted....
-
R409.10.1 Top and Bottom Extension at Ramps
R409.10.1 Top and Bottom Extension at Ramps. Ramp handrails shall extend horizontally above the landing for 305 mm (1.0 ft) minimum beyond the top and bottom of ramp runs....
-
Curb Ramps
Error/Omission: Curb ramp that is located across a circulation path has steep unprotected side flares. Result: People walking across the curb ramp may trip and be injured....
-
Smooth Surface
Section 404.2.10 requires that swinging doors and gates have a smooth surface on the push side that extends their full width....
-
5.1.7 Surface
The surface of the clear ground space shall be firm and stable....
-
106.5.23 Curb Ramp
A short ramp cutting through a curb or built up to it....
