R304.3 Parallel Curb Ramps. Parallel curb ramps shall comply with R304.3 and R304.5....
Search Results "Ramp Surface"
Filters
Commonly Searched Documents
-
R304.3 Parallel Curb Ramps
-
R304.2 Perpendicular Curb Ramps
R304.2 Perpendicular Curb Ramps. Perpendicular curb ramps shall comply with R304.2 and R304.5....
-
11B-406.5 Common requirements
Curb ramps and blended transitions shall comply with Section 11B-406.5....
-
R305.2.1 Perpendicular Curb Ramps
R305.2.1 Perpendicular Curb Ramps. On perpendicular curb ramps, detectable warning surfaces shall be placed as follows: 1....
-
Surface
Surface—The top layer of ground on a recreation site, outdoor recreation access route, trail, or beach access route Firm. A surface that resists deformation by indentations....
-
802.1.1 Floor or Ground Surface
The floor or ground surface of wheelchair spaces shall comply with 302. Changes in level are not permitted. EXCEPTION: Slopes not steeper than 1:48 shall be permitted....
-
802.1.1 Floor or Ground Surface
The floor or ground surface of wheelchair spaces shall comply with 302. Changes in level are not permitted. EXCEPTION: Slopes not steeper than 1:48 shall be permitted....
-
Amramp Portable Ramps
Durable • Easy to Use Great solution for homes or businesses with low-rise entrances Easy-carry handles Easily folded and stored Sizes range from 2 ft to 12 ft
-
Surface, Slope, and Openings [1011.2.2, 1011.2.3, and 1011.2.4]
The surface of the clear ground space must be firm and stable. Additional information on firm and stable surfaces is provided in the trails section of this guide....
-
4.3.6 Surface Textures
The surface of an accessible route shall comply with 4.5....
-
4.3.6 SURFACE TEXTURES
The surface of an accessible route shall comply with 4.5....
-
11B-404.2.10 Door and gate surfaces
Swinging door and gate surfaces within 10 inches (254 mm) of the finish floor or ground measured vertically shall have a smooth surface on the push side extending the full width of the door...
-
11B-404.2.10 Door and gate surfaces
Swinging door and gate surfaces within 10 inches (254 mm) of the finish floor or ground measured vertically shall have a smooth surface on the push side extending the full width of the door...
-
11B-404.2.10 Door and gate surfaces
Swinging door and gate surfaces within 10 inches (254 mm) of the finish floor or ground measured vertically shall have a smooth surface on the push side extending the full width of the door...
-
R304.5.3 Cross Slope
The cross slope of curb ramps, blended transitions, and turning spaces shall be 2 percent maximum....
-
Handrails [§405.8, §505]
Handrails [§405.8, §505] Handrails are required on both sides of ramps with a rise greater than 6”....
-
Acceptable Trail Surfacing Requirements
Trail surfaces are currently considered accessible only if the surfacing material is firm, stable, and slip-resistant and the trail has the engineered attributes of adequate width, moderately...
-
Parallel Curb Ramps
Curb ramps can be oriented parallel to sidewalks. This design provides an option where limited space precludes a top landing....
-
b. Transfer Surface Location
The MDE NPRM proposed the same location and transfer sides of the transfer surface for diagnostic equipment used by patients in the supine, prone, or side-lying position (M301) and diagnostic...
-
Costs to Provide Detectable Warning Surfaces on Curb Ramps (Section-by-Section Analysis)
Costs to Provide Detectable Warning Surfaces on Curb Ramps (Section-by-Section Analysis) Detectable warning surfaces are available in a variety of materials....
-
SECTION 1010 RAMPS
SECTION 1010 RAMPS [DSA-AC] In addition to the requirements of this section, means of egress, which provide access to, or egress from, buildings or facilities where accessibility is...
-
Bonded Impact/cushioning Surfaces
Bonded Impact/cushioning Surfaces Eight different surface test specimens were formed with surface dimensions of 1.2m x 1.2m with a depth of 0.3m (48”x48”x 12”) in Madison WI (Figure 1...
-
1018.3 Surface
The surface of beach access routes and resting intervals shall be firm and stable....
-
1018.3 Surface
The surface of beach access routes and resting intervals shall be firm and stable....
