at rest in the load and unload position, the vertical difference between the floors shall be within plus or minus 5/8 inches (15.9 mm) and the horizontal gap shall be 3 inches (76 mm) maximum...
Search Results "Maximum Reach Depth"
Filters
Commonly Searched Documents
-
11B-1002.4.3 Gaps
-
1002.4.3 Gaps
are at rest in the load and unload position, the vertical difference between the floors shall be within plus or minus 5/8 inches (16 mm) and the horizontal gap shall be 3 inches (75 mm) maximum...
-
1002.4.3 Gaps
are at rest in the load and unload position, the vertical difference between the floors shall be within plus or minus 5/8 inches (16 mm) and the horizontal gap shall be 3 inches (75 mm) maximum...
-
11B-306.2.2 Maximum depth
Toe clearance shall extend 25 inches (635 mm) maximum under an element....
-
11B-306.2.2 Maximum depth
Toe clearance shall extend 25 inches (635 mm) maximum under an element....
-
11B-306.2.2 Maximum depth
Toe clearance shall extend 25 inches (635 mm) maximum under an element....
-
11B-202.5 Alterations to qualified historic buildings and facilities
(3)(i) Alterations to historic properties shall comply, to the maximum extent feasible, with the provisions applicable to historic properties in the design standards specified in §35.151...
-
11B-202.5 Alterations to qualified historic buildings and facilities
(3)(i) Alterations to historic properties shall comply, to the maximum extent feasible, with the provisions applicable to historic properties in the design standards specified in §35.151...
-
11B-202.5 Alterations to qualified historic buildings and facilities
(3)(i) Alterations to historic properties shall comply, to the maximum extent feasible, with the provisions applicable to historic properties in the design standards specified in §35.151...
-
11B-604.8.1.1 Size
Wheelchair accessible compartments shall be 60 inches (1524 mm) wide minimum measured perpendicular to the side wall, and 56 inches (1422 mm) deep minimum for wall hung water closets...
-
11B-604.8.1.1 Size
11B-604.8.1.1 Size. Wheelchair accessible compartments shall be 60 inches (1524 mm) wide minimum measured perpendicular to the side wall, and 56 inches (1422 mm) deep minimum for...
-
11B-604.8.1.1 Size
Wheelchair accessible compartments shall be 60 inches (1524 mm) wide minimum measured perpendicular to the side wall, and 56 inches (1422 mm) deep minimum for wall hung water closets...
-
5.6 Tableware and Condiment Areas
Self-service shelves and dispensing devices for tableware, dishware, condiments, food and beverages shall be installed to comply with 4.2 (see Fig. 54).
-
Verify Electrical
VERIFY ELECTRICAL – remember finish material thicknesses! Heights of all 30 amp or less outlet boxes. Measure to top or bottom of...
-
Verify Electrical
VERIFY ELECTRICAL – remember finish material thicknesses! Heights of all 30 amp or less outlet boxes. Measure to top or bottom of...
-
5.3 TABLEWARE AREAS
Install tableware, dishware, condiment, food and beverage display shelves, and dispensing devices in compliance with 4.2 (see Fig. 54).
-
§ 38.107(a)(4)
(4) Faucets and flush controls shall be operable with one hand and shall not require tight grasping, pinching, or twisting of the wrist. The force required to activate controls shall...
-
F202.3 Alterations
In alterations, where compliance with applicable requirements is technically infeasible, the alteration shall comply with the requirements to the maximum extent feasible. 3....
-
810.6.2 Routes and Destinations
Signs covered by this requirement shall, to the maximum extent practicable, be placed in uniform locations within the system....
-
810.6.2 Routes and Destinations
Signs covered by this requirement shall, to the maximum extent practicable, be placed in uniform locations within the system....
-
4.1.6(3)(f)(ii)
(ii) Where it is technically infeasible to alter all performing areas to be on an accessible route, at least one of each type of performing area shall be made accessible.
-
Site Constraints
Platform lifts are permitted where "existing or other constraints" make ramp or elevator access "infeasible." This is intended to cover altered facilities where limited space or...
-
4.1.6(3)(e)(ii)
(ii) Where it is technically infeasible to install a required standard stall (Fig. 30(a)), or where other codes prohibit reduction of the fixture count (i.e., removal of a water...
-
810.6.2 Routes and Destinations
Signs covered by this requirement shall, to the maximum extent practicable, be placed in uniform locations within the system....