In these cases, the curb ramps installed must meet the accessibility requirements of the ADA to the maximum extent feasible.10 Scoping requirements in the ADA Standards establish limitations...
Search Results "Maximum Reach Depth"
Filters
Commonly Searched Documents
-
3. New Construction vs. Alterations
-
Pilot Rock Varmint Defiant Trash Can Cover
This Cover keeps trash out of reach and puts the door at a comfortable height for depositing trash....
-
233.3.5 Alterations, F233.3.4 Alterations, F233.4.5 Alterations
Amendatory Language For the reasons stated in the preamble, we amend 36 CFR part 1191 as follows: Redesignating sections 233.3.4, 233.3.4.1, and 233.3.4.2 as 233.3.5,...
-
4.1.6(1)(d)
(d) No alteration of an existing element, space, or area of a building or facility shall impose a requirement for greater accessibility than that which would be required for new...
-
Technical difficulty and readily achievable
Along with cost and business operation, the technical feasibility of barrier removal must be taken into consideration. It may be impossible to alter or expand a bathroom due to load...
-
1002.2 Accessible Routes
In load or unload areas and on amusement rides, where compliance with 405.2 is not structurally or operationally feasible, ramp slope shall be permitted to be 1:8 maximum. 2....
-
1002.2 Accessible Routes
In load or unload areas and on amusement rides, where compliance with 405.2 is not structurally or operationally feasible, ramp slope shall be permitted to be 1:8 maximum. 2....
-
1002.2 Accessible Routes
In load or unload areas and on amusement rides, where compliance with 405.2 is not structurally or operationally feasible, ramp slope shall be permitted to be 1:8 maximum. 2....
-
Exceptions When Conditions Do Not Permit Full Compliance
The proposed rule would have required compliance “to the maximum extent feasible” when an exception is used....
-
11B-1002.2 Accessible routes
In load or unload areas and on amusement rides, where compliance with Section 11B-405.2 _|Slope|_ is not structurally or operationally feasible, ramp slope shall be permitted to be 1:8 maximum...
-
11B-1002.2 Accessible routes
In load or unload areas and on amusement rides, where compliance with Section 11B-405.2 _|Slope|_ is not structurally or operationally feasible, ramp slope shall be permitted to be 1:8 maximum...
-
11B-1002.2 Accessible routes
In load or unload areas and on amusement rides, where compliance with Section 11B-405.2 is not structurally or operationally feasible, ramp slope shall be permitted to be 1:8 maximum...
-
11B-1009.4.3 Wall depth and length
The depth of the transfer wall shall be 12 inches (305 mm) minimum and 16 inches (406 mm) maximum....
-
Alterations to Qualified Historic Buildings and Facilities: ADA Standard Section 202.5
Section 202.5 covers the most current ADA Standards for alterations to qualified historic buildings and facilities.
-
202.4 Alterations Affecting Primary Function Areas
to the requirements of 202.3, an alteration that affects or could affect the usability of or access to an area containing a primary function shall be made so as to ensure that, to the maximum...
-
Maximum Force
The Board sought comment on whether the maximum 5 pounds of force was appropriate for operating controls activated by a single finger, such as elevator call and control panel buttons, platform...
-
Substitute cells. (Section-by-Section Analysis)
., cells other than those where alterations are originally planned), provided that each substitute cell is located within the same facility, is integrated with other cells to the maximum...
-
202.4 Alterations Affecting Primary Function Areas
to the requirements of 202.3, an alteration that affects or could affect the usability of or access to an area containing a primary function shall be made so as to ensure that, to the maximum...
-
11B-222.1 General
Where dressing rooms, fitting rooms, or locker rooms are provided, at least 5 percent, but no fewer than one, of each type of use in each cluster provided shall comply with Section...
-
F222.1 General
Where dressing rooms, fitting rooms, or locker rooms are provided, at least 5 percent, but no fewer than one, of each type of use in each cluster provided shall comply with...
-
222.1 General
Where dressing rooms, fitting rooms, or locker rooms are provided, at least 5 percent, but no fewer than one, of each type of use in each cluster provided shall comply with...
-
222.1 General
222.1 General. Where dressing rooms, fitting rooms, or locker rooms are provided, at least 5 percent, but no fewer than one, of each type of use in each cluster provided shall comply...
-
Alterations
In alterations, the minimum number is based on the total number of spaces altered or added to a lot. Recommendation: Where a lot is not fully altered, it is recommended that the...
