Where walls and partitions are required to have a minimum 1-hour fire-resistance rating, recessed fixtures shall be installed such that the required fire resistance will not be reduced....
Search Results "Wing Wall"
Filters
Commonly Searched Documents
-
711.3.2 Membrane penetrations
-
Maneuvering Clearances at Doors [4.13.6]
Clearance to the wall plane next to the door (even when the door is in a recess) is essential....
-
Temporary and Permanent Structures: ADA Standard Section 201.3
Section 201.3 covers the application of the most current requirements for temporary and permanent structures.
-
Transfer Type Shower Compartments: ADA Standard Section 608.2.1
Section 608.2.1 covers the current ADA Standards for the size and clearances of transfer type shower compartments.
-
Seats: ADA Standard Section 608.4
Section 608.4 covers the current ADA Standards for seats in shower compartments.
-
11B-407.4.10 Support rail
Support rails shall be provided on at least one wall of the car. Advisory 11B-407.4.10 Support rail....
-
704.8 Allowable area of openings
Values given are percentage of the area of the exterior wall. b....
-
H22
Is a second horizontal grab bar at least 36 inches long securely mounted on the back wall with one end no more than 6 inches from the side wall 33 to 36 inches above the floor?...
-
M19
Is a horizontal grab bar at least 40 inches long securely mounted on the adjacent side wall 33 to 36 inches above the floor with one end no more than 12 inches from the back wall?...
-
4.3.5.2 180-degree turn
Our research findings for this turn apply to corridors and other circulation spaces are bounded by two parallel walls or three walls....
-
604.3.1 Size
Clearance around a water closet shall be 60 inches (1525 mm) minimum measured perpendicular from the side wall and 56 inches (1420 mm) minimum measured perpendicular from the rear wall....
-
Accessible Pathway & Corridor: Minimum Clear Width Required for 180-degree Turn
These data are based on measurements of wheeled mobility users performing 180-degree turns in a dead-end hallway, built with mock walls....
-
6.3(3)
(3) Each two-bed room shall have a minimum clear floor space of 42 in (1065 mm), preferably 48 in (1220 mm), between the foot of the bed and the wall; 36 in (915 mm) between the side of...
-
11B-809.9.3 Removable base cabinets
following conditions are met: a) base cabinets can be removed without the use of specialized tools or knowledge; b) the finish floor extends under the base cabinet; and c) the walls...
-
M1
.), is a sign with raised characters and Braille mounted on the wall adjacent to the latch side of the door and centered 60 inches above the floor?...
-
Problem Two (Protruding Objects)
Problem Two: A wall-mounted display case protrudes seven inches from the wall and the bottom of the case is 40 inches above the floor....
-
711.3.1 Through penetrations
Through penetrations of fire-resistance-rated walls shall comply with Section 711.3.1.1 or 711.3.1.2....
-
2.2.4 Maneuverability
tasks: • 90-degree turn, • 180-degree turn with no restrictions on length of the maneuver, • 180-degree with a center barrier, • 360-degree rotation within a space with four walls...
-
Meeting ANSI Standard S12.60 Requirements
the wall height increases above ten feet....
-
11B-609.3 Spacing
of 6 inches on either side of the inside corner between two adjacent wall surfaces....
-
11B-609.3 Spacing
of 6 inches on either side of the inside corner between two adjacent wall surfaces....
-
11B-609.3 Spacing
of the inside corner between two adjacent wall surfaces....
-
H21
Is a horizontal grab bar at least 40 inches long securely mounted on the adjacent side wall 33 to 36 inches above the floor with one end no more than 12 inches from the back wall 33 to 36...
-
11B-610.3.1 Rectangular seats
The rear edge of a rectangular seat shall be 2½ inches (64 mm) maximum and the front edge 15 inches (381 mm) minimum and 16 inches (406 mm) maximum from the seat wall....