be relocated to between 48 inches measured to the baseline of the lowest tactile character and 60 inches measured to the baseline of the highest tactile character above the finish floor surface...
Search Results "Curb Ramp Surface"
-
D. Signage
-
A. Accessible Entrance
Accessible Entrance Having a way to get into the emergency shelter on a surface that is firm, stable, slip resistant, without steps or steep slopes, and wide enough for a person using...
-
11B-411.2.1.6 Identification of floors served
consoles located on floors with a building entry, including parking and transfer levels, shall be provided with signage complying with Sections 11B-703.2, 11B-703.3, and 11B-703.5 on the surface...
-
4.4.1 General
In alterations, where a condition for exception in section 1.1 prohibits full compliance with a specific requirement for clear floor or ground space surface, slope, size, or location, the...
-
11B-411.2.1.6 Identification of floors served
consoles located on floors with a building entry, including parking and transfer levels, shall be provided with signs complying with Sections 11B-703.2, 11B-703.3, and 11B-703.5 on the surface...
-
11B-602.9 Pedestrian protection
When used, wing walls or barriers shall project horizontally at least as far as the drinking fountain and to within 6 inches (152 mm) vertically from the floor or ground surface....
-
11B-1005.2.1 Height
At least 25 percent of the railings, guards, or handrails shall be 34 inches (864 mm) maximum above the ground or deck surface....
-
11B-411.2.1.6 Identification of floors served
consoles located on floors with a building entry, including parking and transfer levels, shall be provided with signs complying with Sections 11B-703.2, 11B-703.3, and 11B-703.5 on the surface...
-
11B-1005.2.1 Height
At least 25 percent of the railings, guards, or handrails shall be 34 inches (864 mm) maximum above the ground or deck surface....
-
ASME
standard includes additional provisions for runway enclosures, electrical equipment and wiring, structural support, headroom clearance (which is 80 inches minimum), lower level access ramps...
-
Bradley 20.6 Gallon Waste Receptacle 355
Model 355 Surface Mounted 20.6 Gallon Capacity Surface Mounted...
-
Access to Programs and Services in Existing Facilities
If a public library is inaccessible, staff can provide curb-side service for a patron with a mobility disability to check out and return books Structural changes are not required where...
-
What is a "reasonable accommodation"?
Some of the most common types of accommodations include: physical changes, such as installing a ramp or modifying a workspace or restroom; sign language interpreters for people...
-
Accessibility to Perform the Essential Functions of the Job
Examples of accommodations that may be needed to make facilities accessible and usable include: installing a ramp at the entrance to a building; removing raised thresholds...
-
Part One: The ADA’s Requirements for Small Towns
A ramp located next to the stairs to this town hall provides an accessible entrance. 1 The term "towns" is used in this publication to refer to all small local governments, towns, and...
-
10 - foot straightedge method
For ramps ACI 117 refers to RMS Levelness tolerance as defined in paragraph 4.11 in ASTM E - 1486....
-
Stanley FBB 269 Heavy Weight Ball Bearing “Swing Clear” Offset Door Hinge
clear 90° Equipped with four Stanley permanently lubricated non-detachable ball bearings Pins in nonferrous hinges are stainless steel Heavy weight gauges increase available bearing surface...
-
Stanley FBB 266 Heavy Weight Ball Bearing “Swing Clear” Offset Door Hinge
clear 90° Equipped with four Stanley permanently lubricated non-detachable ball bearings Pins in nonferrous hinges are stainless steel Heavy weight gauges increase available bearing surface...
-
Stanley FBB 268 Heavy Weight Ball Bearing “Swing Clear” Offset Door Hinge
clear 90° Equipped with four Stanley permanently lubricated non-detachable ball bearings Pins in nonferrous hinges are stainless steel Heavy weight gauges increase available bearing surface...
-
Stanley FBB 264 Heavy Weight Ball Bearing “Swing Clear” Offset Door Hinge
clear 90° Equipped with four Stanley permanently lubricated non-detachable ball bearings Pins in nonferrous hinges are stainless steel Heavy weight gauges increase available bearing surface...
-
Shared Use Paths: ADA Standard Section 2.
address access to sidewalks, streets, and other pedestrian facilities, provide requirements for pedestrian access routes, including specifications for route width, grade, cross slope, surfaces...
-
11B-609.3 Spacing
Section 11B-609.9 the space between the walls and the grab bar shall be 1½ inches (38 mm) minimum for a distance of 6 inches on either side of the inside corner between two adjacent wall surfaces...
-
11B-609.3 Spacing
Section 11B-609.9 the space between the walls and the grab bar shall be 1½ inches (38 mm) minimum for a distance of 6 inches on either side of the inside corner between two adjacent wall surfaces...
-
11B-705.1.2.3 Islands or cut-through medians
cut-through less 2 inches (51 mm) maximum on each side, placed at the edges of the pedestrian island or cut-through median, and shall be separated by 24 inches (610 mm) minimum of walking surface...
