This provision requires that parts creating joints in the smooth surface are to be within 1/16 inch of the same plane as the other....
Search Results "Grade 1 Braille"
Commonly Searched Documents
-
Smooth Surface
-
§ 382.5 Individual with a disability
As used in this definition, the phrase: (a) Physical or mental impairment means: (1) any physiological disorder or condition, cosmetic disfigurement, or anatomical loss affecting one...
-
§382.3 Individual with a disability
As used in this definition, the phrase: (a) Physical or mental impairment means: (1) Any physiological disorder or condition, cosmetic disfigurement, or anatomical loss affecting one...
-
F104.1.1 Construction and Manufacturing Tolerances
For example, if this document requires "1½ inches," avoid specifying "1½ inches plus or minus X inches."...
-
Passing Spaces [1016.4]
When passing spaces and resting intervals overlap, the technical requirements for resting intervals apply and the slope of the surface must be no steeper than 1:48 (2 percent) in any direction...
-
M301.2.3 Transfer Sides
Obstructions shall not be vertically less than 1" (25 mm) nor be horizontally more than 3" (75 mm) from the edge of the patient support surface provide unobstructed access to the transfer...
-
NAADAC Webinar Series: "ADA: The Next Generation" - Virtual and At-Home Training
ADA: The Next Generation: Seven Part Webinar Series (total 12 hours): Overview of Title II and III Regulations, Part 1 (10/6/10), Run time: 1.5 hrs Overview of Title II...
-
Video remote interpreting (VRI) services. (Section-by-Section Analysis)
36.303(f) of the NPRM, the Department proposed the inclusion of four performance standards for VRI (which the NPRM termed video interpreting services (VIS)), for effective communication: (1)...
-
COMMERCIAL FACILITIES
Commercial facilities shall not include (1) facilities that are covered or expressly exempted from coverage under the Fair Housing Act of 1968, as amended (42 U.S.C. 3601 - 3631); (2) aircraft...
-
1013.3 Height
Required guards shall not be less than 42 inches (1067 mm) high, measured vertically as follows: 1. From the adjacent walking surfaces; 2. ...
-
1017.4 Passing Spaces
Where passing spaces and resting intervals overlap, the technical requirements for resting intervals in 1017.8.3 require the slope of the surface to not be steeper than 1:48 in any direction...
-
Section 1194.26 Desktop and Portable Computers (Preamble, Section-by-Section Analysis)
These provisions are addressed further in sections 1194.23 (k) (1) through (4) above. (See §1194.23(a) in the NPRM.)...
-
Accessible Routes - Interior and Exterior
ADA Standards 4.1.2 (1); 4.1.3(1); 4.3. At least one route that is a minimum of 36 inches wide without steps, stairs, or other abrupt level changes must be provided...
-
COMMERCIAL FACILITIES
Commercial facilities shall not include (1) facilities that are covered or expressly exempted from coverage under the Fair Housing Act of 1968, as amended (42 U.S.C. 3601 - 3631); (2) aircraft...
-
COMMERCIAL FACILITIES
Commercial facilities shall not include (1) facilities that are covered or expressly exempted from coverage under the Fair Housing Act of 1968, as amended (42 U.S.C. 3601 - 3631); (2) aircraft...
- TownSteel "V" Rose Tubular Lockset
- TownSteel "L" Rose Tubular Lockset
- TownSteel "S" Rose Tubular Lockset
- TownSteel "B" Rose Tubular Lockset
- TownSteel "C" Rose Tubular Lockset
- TownSteel "H" Rose Tubular Lockset
- TownSteel "F" Rose Tubular Lockset
- AJW Architectural Products U719 96"W x 48"H J-Mold Mirror - Four Sided Frame - Plate Glass
-
3.2 Non-discrimination Legislation.
The following websites contain relevant information concerning disability legislation and how it applies to an airport setting. 1....