The transfer surface shall be 30 inches (760 mm) wide minimum and 15 inches (381mm) deep minimum. Advisory M301.2.2 Size. The size requirements in this section apply only to the...
Search Results "Positioning Aids"
-
M301.2.2 Size
-
M301.2 Transfer Surface
A transfer surface shall be provided and shall comply with M301.2.
-
STATE AND LOCAL GOVERNMENTS
State and local governments must reasonably modify their policies, practices, and procedures; must provide auxiliary aids and services necessary for effective communication; and must make...
-
§ 36.311 Mobility devices.
[See subsections ...]
-
A. Non-Discrimination
. § 36.302; Atlantis will furnish appropriate auxiliary aids and services, free of charge, when necessary to ensure effective communication with individuals with disabilities...
-
M302.3.2 Leg Supports (Section-by-Section Analysis)
The MDE NPRM did not propose to require stirrups to provide a method of supporting, positioning, and securing the patient’s legs for diagnostic equipment used by patients in the seated position...
-
PROVIDING ACCESSIBLE VOTING SYSTEMS AND EFFECTIVE COMMUNICATION
Only if providing an aid or service would result in a fundamental alteration or undue financial and administrative burdens is a jurisdiction not required to provide the aid or service. ...
-
TECHNIQUES FOR OFFICERS TO COMMUNICATE EFFECTIVELY
Officers may utilize the following auxiliary aids, when available, to communicate effectively: --Use of gestures; --Use of visual aids; --Use of a...
-
M305.2.4.1 Circular Cross Section
Transfer supports with circular cross sections shall have an outside diameter of 1 ¼ inches (32 mm) minimum and 2 inches (51 mm) maximum.
-
M305.2.1.2 Side Transfer Supports
Transfer supports for transfer surfaces complying with M301.2.3.2 shall be capable of supporting transfer on each side of the transfer surface.
-
M305.2.1.1 End Transfer Supports
Transfer supports for transfer surfaces complying with M301.2.3.1 and M302.2 shall be located on the short side (length) opposite the transfer side.
-
5.2.2.2 Transfer Surface Depth Recommendation for M302
5.2.2.2 Transfer Surface Depth Recommendation for M302 The Committee recommends a minimum depth requirement of 17 inches for equipment used by patients in seated positions....
-
5.2.2 Transfer Surface Size Recommendations for M302
5.2.2 Transfer Surface Size Recommendations for M302 Description: The transfer surface is the part of the diagnostic equipment onto which patients who use mobility devices or aids transfer...
-
5.2.2.1 Transfer Surface Width Recommendations for M302
Recommendations for M302 The Committee recommends 21 inches for the minimum width of the transfer surface of examination chairs and other equipment primarily used by patients in a seated position...
-
11. Must a student be eligible under the IDEA in order to be provided auxiliary aids and services needed to ensure effective communication under Title II? (In other words, must a student with a disability have an IEP to access effective auxiliary aids and services?)
many students who have communication needs based on a hearing, vision, or speech disability are eligible under the IDEA and have IEPs, these are not prerequisites for receiving auxiliary aids...
-
M301.3.2 Leg Supports
Where stirrups are provided, leg supports shall also be provided and shall comply with M305.4.
-
E102.3 ANSI/IEEE (Section-by-Section Analysis)
Products conforming to this standard minimize interference to hearing aids by wireless telephones....
-
M305.2.4.2 Non-Circular Cross Section
Transfer supports with non-circular cross sections shall have a cross-section dimension of 2 inches (51 mm) maximum and a perimeter dimension of 4 inches (100 mm) minimum and 4.8...
-
5.3.1 Permitted Obstructions to Transfer Sides for M301 and M302
5.3.1 Permitted Obstructions to Transfer Sides for M301 and M302 Description: Transfer side provisions are the same for M301 and M302 and require the transfer surface to be...
-
407.4.8.2.3 Frequency
The verbal annunciator shall have a frequency of 300 Hz minimum to 3000 Hz maximum.
-
407.4.8.1.2 Location
Indicators shall be located above the car control panel or above the door.
-
11B-407.4.8.1.2 Location
Indicators shall be located above the car control panel or above the door.
-
11B-407.4.8.2.3 Frequency
The verbal annunciator shall have a frequency of 300 Hz minimum to 3000 Hz maximum.
-
Grab Bar and Backrest Evaluation
Grab bar and backrest preferences were reported in this study with the tall grab bar and the short backrest being selected more often than the short grab bars and medium and tall...