Visible indicators shall comply with Section 11B-411.4.8.1.
Search Results "Positioning Aids"
-
11B-411.4.8.1 Visible indicators
-
Size: ADA Standard Section 407.4.8.1.1
Section 407.4.8.1.1 covers the current ADA Standards for size of visible elevator car position indicators.
-
11B-407.4.8.2.1 Signal type
The signal shall be an automatic verbal annunciator which announces the floor at which the car is about to stop. Exception: For elevators that have a rated speed of 200 feet per...
-
11B-411.4.8.1 Visible indicators
Visible indicators shall comply with Section 11B-411.4.8.1.
-
11B-407.4.8.1.1 Size
Characters shall be ½ inch (12.7 mm) high minimum.
-
What employment practices are covered by the ADA?
HIV or AIDS....
-
5.4.8 Transfer Support Gripping Surface Hazard Recommendation for M301 and M302
Sharp edges or abrasive elements may injure and cause the patient to lose his/her grip during positioning or transfer....
-
§35.130(f) (Section-by-Section Analysis)
Such measures may include the provision of auxiliary aids or of modifications required to provide program accessibility....
-
Ensure that communication with people with disabilities is as effective as communication with people without disabilities
Take appropriate steps to ensure that communication with people with disabilities is as effective as communication with people without disabilities, and provide auxiliary aids and...
-
5.9.1 Standing Supports In Reference To Mammography Equipment
To be useful, positioning supports must be shaped for grasping, positioned within reach range of all users, and be 12 inches long minimum when located on the moving C-arm or 18 inches long...
-
5.1 Transfer Surface Height
5.1 Transfer Surface Height
-
5.1.4 Transfer Surface Height Measurement
5.1.4 Transfer Surface Height Measurement. The transfer surface height should be measured from the floor to the highest point on the seat in an uncompressed state, inclusive of...
-
Conference Proceedings and Final Passage
In each case (and with amendments in a few cases), the Senate conferees conceded the House position....
-
M305.2.2 Length
The length of transfer supports shall comply with M305.2.2.1 or M305.2.2.2.
-
§ 1194.23(i)
(i) Interference to hearing technologies (including hearing aids, cochlear implants, and assistive listening devices) shall be reduced to the lowest possible level that allows a user of...
-
M305.3.1.1 Horizontal Position
The length of gripping surfaces on horizontal standing supports shall be 4 inches (100 mm) minimum except for diagnostic equipment containing a wheelchair space which shall comply...
-
M305.3.2.1 Horizontal Position
The height of the top of the gripping surface on horizontal standing supports shall be 34 inches (865 mm) minimum and 38 inches (965 mm) maximum above the standing surface.
-
5.5.1 Armrest Provision for M302
5.5.1 Armrest Provision for M302 Description: Diagnostic equipment used by patients in a seated position such as exam chairs typically have armrests....
-
Section 36.311 Mobility Devices (Section-by-Section Analysis)
Section 36.311 set forth specific requirements for the accommodation of mobility devices, including wheelchairs, manually-powered mobility aids, and other power-driven mobility devices....
-
Armrests (M302.3.2)
M302.3.2 would require armrests to be provided on diagnostic equipment used by patients in a seated position....
-
Neckloop (BE9159/BE9161)
The Neckloop can be used with any hearing aids that have telecoil....
-
M305.2.8 Fittings
Transfer supports shall not rotate within their fittings when in place for transfer.
-
M305.2.7 Clearance
Clearance between the transfer support gripping surface and adjacent surfaces or obstructions shall be 1 ½ inches (38 mm) minimum.
-
M305.2.7 Clearance (Section-by-Section Analysis)
In the MDE NPRM, the Access Board did not provide any specific requirements for clearances around the transfer support. However, in the preamble to the MDE NPRM the Access Board...
