The provisions of Division 9 shall apply where required by Division 2 or where referenced by a requirement in this chapter....
Search Results "9-1-1 Service"
-
11B-901.1 Scope
-
11B-901.1 Scope
The provisions of Division 9 shall apply where required by Division 2 or where referenced by a requirement in this chapter....
-
18(b)
required number of accessible rooms for individuals with mobility disabilities that comply with the ADA Standards for maneuvering clearances between and around the beds (ADA Standards §9.2.2(1)...
-
18(a)
required number of accessible rooms for individuals with mobility disabilities that comply with the ADA Standards for maneuvering clearances between and around the beds (ADA Standards §9.2.2(1)...
-
2. Executive Summary
for the accessibility standards adopted by DOJ for the design, construction, and alteration of facilities (other than certain transportation facilities) by entities subject to the ADA.9...
-
28 CFR Part 35 Nondiscrimination on the Basis of Disability in State and Local Government Services (2010 ADA Title II Regulations with amendments issued through Aug. 2016)
DEPARTMENT OF JUSTICE 28 CFR Part 35 [CRT Docket No. 105; AG Order No. 3180–2010] RIN 1190–AA46 Nondiscrimination on the Basis of Disability in State and Local Government Services...
-
11B-502.4 Floor or ground surfaces
Exception: Slopes not steeper than 1:48 shall be permitted. [2010 ADAS] Advisory 502.4 Floor or Ground Surfaces. ...
-
Section 4.1.6, Alterations (Preamble, Section-by-Section Analysis)
First, if any existing element or space is altered, the altered element or space must meet new construction requirements (section 4.1.6(1)(b))....
-
11B-502.4 Floor or ground surfaces
Exception: Slopes not steeper than 1:48 shall be permitted. [2010 ADAS] Advisory 502.4 Floor or Ground Surfaces. ...
-
11B-502.4 Floor or ground surfaces
Changes in level, slopes exceeding 1:48, and detectable warnings shall not be permitted. Exception: Reserved. Advisory 11B-502.4 Floor or ground surfaces....
-
706.2 Receiver Jacks
Receivers required for use with an assistive listening system shall include a 1/8 inch (3.2 mm) standard mono jack. [ECTCR UFAS 4.33.7]...
-
609.2.1 Circular Cross Section
Grab bars with circular cross sections shall have an outside diameter of 1¼ inches (32 mm) minimum and 2 inches (51 mm) maximum....
-
802.1.1 Floor or Ground Surface
EXCEPTION: Slopes not steeper than 1:48 shall be permitted....
-
M305.2.4.1 Circular Cross Section
Transfer supports with circular cross sections shall have an outside diameter of 1 ¼ inches (32 mm) minimum and 2 inches (51 mm) maximum....
-
M303.3.2 Beveled
Changes in level between ¼ inch (6.4 mm) high and ½ inch (13 mm) high maximum shall be beveled with a slope not steeper than 1:2....
-
802.1.1 Floor or Ground Surface
EXCEPTION: Slopes not steeper than 1:48 shall be permitted....
-
409.4.4 Leveling
Each car shall automatically stop at a floor landing within a of 1/2 inch (13 mm) under rated loading to zero loading conditions....
-
Individual captioning device (Section-by-Section Analysis)
In § 36.303(g)(1)(iv), the Department is proposing to define “individual captioning device” as “the individual device that patrons may use at their seats to view the closed captions.”...
-
T303.3.2 Handrail and Stanchion Circular Cross Section
Handrails and stanchions with a circular cross section shall have an outside diameter of 1¼ inches (32 mm) minimum and 2 inches (50 mm) maximum....
-
Figure 11B-407.2.3.1 Floor designation
Revises the braille designation on the figure to correctly indicate the number 1 and revises figure title....
-
706.2 Receiver Jacks
Receivers required for use with an assistive listening system shall include a 1/8 inch (3.2 mm) standard mono jack....
-
11B-609.2.1 Circular cross section
Grab bars with circular cross sections shall have an outside diameter of 1¼ inches (32 mm) minimum and 2 inches (51 mm) maximum....
-
Sec. 12164. Regulations. [Section 244]
Not later than 1 year after July 26, 1990, the Secretary of Transportation shall issue regulations, in an accessible format, necessary for carrying out this subpart....
-
505.5 Clearance
Clearance between handrail gripping surfaces and adjacent surfaces shall be 1½ inches (38 mm) minimum. Figure 505.5 Handrail Clearance...