Only approved DSA-AC detectable warning products and directional surfaces shall be installed as provided in the California Code of Regulations (CCR), Title 24, Part 1, Chapter 5, Articles...
Search Results "Side Transfer Surface"
-
11B-705.3 Product Approval
-
11B-407.4.10 Support rail
Support rails in elevator cabs are used in a different way than handrails along a walking surface such as a ramp or stairway....
-
DETECTABLE WARNING
A standardized surface feature built in or applied to walking surfaces or other elements to warn persons with visual impairments of hazards on a circulation path....
-
R207.1 General
The curb ramp (excluding any flared sides) or blended transition shall be contained wholly within the width of the pedestrian street crossing served....
-
Are doors or gates to employee work areas required to comply?
Full compliance of doors or gates on the interior side is recommended, but not required....
-
Willoughby Industries WBL-2320 Ligature-resistant Behavioral Healthcare Lavatory System
Exposed stainless steel surfaces shall be polished to a #4 satin finish and shall be fully-rounded to minimize use as a ligature point....
-
Magnuson Group 2000 Series Magazine Racks
Available with one, two, three or four pocket configurations, these racks can be installed with or without wood side panels....
-
Season tickets and multiple event sales. (Section-by-Section Analysis)
The rule also states that spectators purchasing tickets for accessible seating on a multi-event basis shall be permitted to transfer tickets for single-event use by friends or associates...
-
Season tickets and multiple event tickets. (Section-by-Section Analysis)
The rule also states that spectators purchasing tickets for accessible seating on a multi-event basis shall be permitted to transfer tickets for single-event use by friends or associates...
-
Mockett DH4/DH5 Installation Video
Lightweight, yet sturdy and durable, these subtle complementary pulls will enhance the overall design of any door surface....
-
1. Number of TTYs
Transferring a TTY call from a non-TTY capable answering position to a TTY-dedicated position may result in the call being disconnected or undue delay in answering the call....
-
Tread Width
The visible trail surface measured perpendicular to the direction of travel....
-
AJW Architectural Products US712 Series U7128B-1216 12"Wx16"H Security Concealed Mount Mirror, Angle Frame, Stainless Steel Surface
Product Features fabricated of #14 gauge stainless steel with a #4 satin finish Hooks Collapse To Prevent Injury Product Has Security Applications Product Specs Frame:...
-
801.1 Scope
For example, 806 addresses guest rooms in transient lodging facilities while 902 contains the technical specifications for dining surfaces....
-
801.1 Scope
For example, 806 addresses guest rooms in transient lodging facilities while 902 contains the technical specifications for dining surfaces....
-
M301.4.2 Clearance Around Base
The base of the equipment shall provide a clearance 6 inches (150 mm) high minimum measured from the floor and 36 inches (915 mm) deep minimum measured from the edge of the examination surface...
-
903.4 Back Support
Back support shall be 42 inches (1065 mm) long minimum and shall extend from a point 2 inches (51 mm) maximum above the seat surface to a point 18 inches (455 mm) minimum above the seat...
-
M302.4.2 Clearance Around Base
The base of the equipment shall provide a clearance 6 inches (150 mm) high minimum measured from the floor and 36 inches (915 mm) deep minimum measured from the edge of the examination surface...
-
1132A.2 Interior doors and secondary exterior doors
The provisions of this section shall apply to the dwelling unit side of doors leading from the interior of the dwelling unit to an unfinished basement or an attached garage....
-
802.1.3 Depth
Where a wheelchair space can be entered only from the side, the wheelchair space shall be 60 inches (1525 mm) deep minimum....
-
604.9.5 Flush Controls
Flush controls shall be located on the open side of the water closet except in ambulatory accessible compartments complying with 604.8.2....
-
Common Problems with Routes to Building Entrances
Ø Ramps are too steep or go too long without level rest areas; handrails are not provided on both sides....
-
604.3.1 Size
Clearance around a water closet shall be 60 inches (1525 mm) minimum measured perpendicular from the side wall and 56 inches (1420 mm) minimum measured perpendicular from the rear wall....
-
5.9.2.1 Standing Supports on Single Ramped Entry Raised Platforms with Wheelchair Spaces
Standing supports should be located on both sides of platforms, a minimum of 34 inches between supports, integrated into the platform, and 32 inches minimum length (at least 80% of the platform...
