them from outside the vehicle while starting to board, and to continue to use them throughout the boarding process, and shall have the top between 30 inches and 38 inches above the ramp surface...
Search Results "Side Transfer Surface"
Filters
Commonly Searched Documents
-
§ 38.83(c)(8) Handrails
-
§ 38.125(c)(8) Handrails
grasp them from outside the car while starting to board, and to continue to use them throughout the boarding process, and shall have the top between 30 inches and 38 inches above the ramp surface...
-
What Are Testing Accommodations?
Examples of the wide range of testing accommodations that may be required include: Braille or large-print exam booklets; Screen reading technology; Scribes to transfer...
-
Fixed Shower Head Height
Commenters urged the Board to retain this exception due to problems with vandalism which would increase maintenance at accessible transfer showers. Response....
-
5.7.1.1 Lift Compatibility Clearance in Base for Stretchers (M301)
shorter wheelbase than “standard,” the clearance for a lift may use both the clearance in the base and the clearance around the base to position the lift around the stretcher for patient transfers...
-
H. Men's Spa and Fitness Center Locker Room
Clear space sufficient to allow a person using a wheelchair to make a parallel transfer onto the bench will be provided. 2010 Standards §§ 222.1, 305, 803.4, and 903....
-
Space Allowance and Reach Ranges [4.2]
For example, the specified height of toilets and shower seats (17-19 inches) approximates the standard seat height of manual wheelchairs to facilitate transfer....
-
409.1 General
For example, an event ticket might be transferred to a smart phone or PDA....
-
810.6.3 Station Names
Signs shall be clearly visible and within the sight lines of standing and sitting passengers from within the vehicle on both sides when not obstructed by another vehicle....
-
810.6.3 Station Names
Signs shall be clearly visible and within the sight lines of standing and sitting passengers from within the vehicle on both sides when not obstructed by another vehicle....
-
11B-806.2.3.1 Personal lift device floor space
The clear space shall extend under the bed parallel to the long side and be adjacent to an accessible route....
-
D2. Clear Passage
Does at least one door or one side of a double leaf door at the accessible entrance provide at least 32 inches clear passage width when the door is open 90 degrees?...
-
Verify Rough Plumbing
Location of toilet flanges from walls. 11B-604.2 Location of lavatory traps from side walls. 11B-606.6 Location of...
-
Verify Rough Plumbing
Location of toilet flanges from walls. 11B-604.2 Location of lavatory traps from side walls. 11B-606.6 Location of...
-
Detail
Participants wanted to experience all sides of the buildings. The models aren’t full rounds....
-
Knee Clearance: Clearance as Measured from Anterior-Most Point - Manual Wheelchair
Hence, to accommodate a particular percentage of users, the side profile of a design element (shown by dotted line) should not extend outside the corresponding shaded area....
-
Knee Clearance: Clearance as Measured from Dorsal Foot Point - Manual Wheelchair
Hence, to accommodate a particular percentage of users, the side profile of a design element (shown by dotted line) should not extend outside the corresponding shaded area....
-
11B-802.1.2 Width
It should be noted that although side access to the wheelchair space is allowed, fixed companion seating also must be provided adjacent to each wheelchair space.◼...
-
11B-806.2.3.1 Personal lift device floor space
The clear space shall extend under the bed parallel to the long side and be adjacent to an accessible route....
-
11B-806.2.3.1 Personal lift device floor space
The clear space shall extend under the bed parallel to the long side and be adjacent to an accessible route....
-
11B-1009.3.1 Sloped entries
Exception: Where sloped entries are provided, the surfaces shall not be required to be slip resistant....
-
R407.9.2 Curb or Barrier
A curb or barrier shall be provided that prevents the passage of a 100 mm (4 in) diameter sphere, where any portion of the sphere is within 100 mm (4 in) of the finish surface....
-
T702.8 Contrast
Where provided, protective surfaces over signs shall have a non-glare finish....
-
1009.3.1 Sloped Entries
Sloped entries shall comply with Chapter 4 except as modified in 1109.3.1 through 1109.3.3 EXCEPTION: Where sloped entries are provided, the surfaces shall not be required to be slip...