This provision requires that parts creating joints in the smooth surface are to be within 1/16 inch of the same plane as the other....
Search Results "Enhanced 9-1-1"
Filters
Commonly Searched Documents
-
Smooth Surface
-
§ 382.5 Individual with a disability
As used in this definition, the phrase: (a) Physical or mental impairment means: (1) any physiological disorder or condition, cosmetic disfigurement, or anatomical loss affecting one...
-
§382.3 Individual with a disability
As used in this definition, the phrase: (a) Physical or mental impairment means: (1) Any physiological disorder or condition, cosmetic disfigurement, or anatomical loss affecting one...
-
F104.1.1 Construction and Manufacturing Tolerances
For example, if this document requires "1½ inches," avoid specifying "1½ inches plus or minus X inches."...
-
Passing Spaces [1016.4]
When passing spaces and resting intervals overlap, the technical requirements for resting intervals apply and the slope of the surface must be no steeper than 1:48 (2 percent) in any direction...
-
M301.2.3 Transfer Sides
Obstructions shall not be vertically less than 1" (25 mm) nor be horizontally more than 3" (75 mm) from the edge of the patient support surface provide unobstructed access to the transfer...
-
NAADAC Webinar Series: "ADA: The Next Generation" - Virtual and At-Home Training
ADA: The Next Generation: Seven Part Webinar Series (total 12 hours): Overview of Title II and III Regulations, Part 1 (10/6/10), Run time: 1.5 hrs Overview of Title II...
-
Video remote interpreting (VRI) services. (Section-by-Section Analysis)
36.303(f) of the NPRM, the Department proposed the inclusion of four performance standards for VRI (which the NPRM termed video interpreting services (VIS)), for effective communication: (1)...
-
COMMERCIAL FACILITIES
Commercial facilities shall not include (1) facilities that are covered or expressly exempted from coverage under the Fair Housing Act of 1968, as amended (42 U.S.C. 3601 - 3631); (2) aircraft...
-
1013.3 Height
Required guards shall not be less than 42 inches (1067 mm) high, measured vertically as follows: 1. From the adjacent walking surfaces; 2. ...
-
34 CFR Part 104 Discrimination on the Basis of Disability in Federally Assisted Programs and Activities - Notice of interpretation
for Accessible Design as defined in the Americans with Disabilities Act (ADA) Title II regulation (referred to in this notice as the 2010 Title II ADA Standards) except that Exception (1)...
-
1017.4 Passing Spaces
Where passing spaces and resting intervals overlap, the technical requirements for resting intervals in 1017.8.3 require the slope of the surface to not be steeper than 1:48 in any direction...
-
Paragraph (b) (Advisory Guidance)
Paragraph (b) Operable with Low Vision and Limited or no Hearing 1. Individuals with low vision often also have hearing disabilities, especially older individuals....
-
Section 1194.26 Desktop and Portable Computers (Preamble, Section-by-Section Analysis)
These provisions are addressed further in sections 1194.23 (k) (1) through (4) above. (See §1194.23(a) in the NPRM.)...
-
Accessible Routes - Interior and Exterior
ADA Standards 4.1.2 (1); 4.1.3(1); 4.3. At least one route that is a minimum of 36 inches wide without steps, stairs, or other abrupt level changes must be provided...
-
COMMERCIAL FACILITIES
Commercial facilities shall not include (1) facilities that are covered or expressly exempted from coverage under the Fair Housing Act of 1968, as amended (42 U.S.C. 3601 - 3631); (2) aircraft...
-
COMMERCIAL FACILITIES
Commercial facilities shall not include (1) facilities that are covered or expressly exempted from coverage under the Fair Housing Act of 1968, as amended (42 U.S.C. 3601 - 3631); (2) aircraft...
-
Rockwood Manufacturing Company 603 Door Guard - Cast Aluminum
Material: Cast Aluminum Options: 1/8" clear plastic shim - order separately as 603 SHIM....
-
Rockwood Manufacturing Company No: 806 Medium Coat Hook
. #6 x 3/4 OH WS Size: 1-1/16"w x 1-1/4"h Projection: 3-1/8" Weight: 1.9 lbs./10 ANSI A156.16: L03111 Most of Rockwood's products are available in a wide variety of architectural finishes...
-
Bobrick 48" Straight Grab Bar B-6806 x 48
48" (1220) long, 1-1/2" dia. tubing. Constructed of 18-gauge (1.2mm), type 304 satin-finish stainless steel tubing....
-
Gamco Horizontal Shower Grab Bar - 45
Description 30" x 30" (762 x 762mm). 125 Series - 1 1/4" (32mm) diameter stainless steel. 150 Series - 1 1/2" (38mm) diameter stainless steel....
-
3.2 Non-discrimination Legislation.
The following websites contain relevant information concerning disability legislation and how it applies to an airport setting. 1....
-
1.4 Related Reading Material.
1. DOJ ADA, Title II, Technical Assistance Manual, and Supplements, http://www.ada.gov/taman2.html. 2....
-
Tax Credit and Deduction
comply with the ADA, the Internal Revenue Service (IRS) Code includes a Disabled Access Credit (Section 44) for businesses with 30 or fewer full-time employees or with total revenues of $1...
