The slopes of the undisturbed site measured between the planned entrance and all vehicular or pedestrian arrival points within 50 feet (15 240 mm) of the planned entrance exceed 15 percent...
Search Results "Tape Measure"
Filters
Commonly Searched Documents
-
TEST NO. 1 – INDIVIDUAL BUILDING TEST
-
TEST NO. 1 – INDIVIDUAL BUILDING TEST
It is not required by this code to provide an accessible route when the terrain of the site is such that both of the following apply: The slopes of the undisturbed site measured between...
-
11B-233.3.1.2.6.2 Test number one, individual building test
The slopes of the undisturbed site measured in a straight line between the planned entrance and all vehicular or pedestrian arrival points within 50 feet (15,240 mm) of the planned entrance...
-
Identification: ADA Standard Section 502.6
Section 502.6 covers the current ADA Standards for parking space identification signs.
-
General: ADA Standard Section 306.1
Section 306.1 of the ADA Standards covers information in the current ADA Standards for knee and toe clearance.
-
Visible Signals: ADA Standard Section 407.2.2.2
Section 407.2.2.2 covers the current ADA Standards for elevator visible signals.
-
11B-604.9.6 Dispensers
Toilet paper dispensers shall comply with Section 11B-309.4 and shall be 7 inches (178 mm) minimum and 9 inches (229 mm) maximum in front of the water closet measured to the centerline of...
-
2013 & 2016 CBC Answer
X3 measurement has no code basis. Both X1 and X2 measurement are acceptable if minimum width of 108 inches are achieved....
-
Purpose of the project
Purpose of the project Accessibility standards reference industry guidance in the measure of field and construction tolerances....
-
1 [§ 4.7.3]
1 [§ 4.7.3] Only measure the width of the ramp section of the curb ramp (labeled “ramp” to the right [below]). The ramp section of a curb ramp is also known as the “ramp run.”...
-
11B-407.2.1.1 Height
Call buttons and keypads shall be located within one of the reach ranges specified in Section 11B-308, measured to the centerline of the highest operable part. Exception: Reserved....
-
Door Pressure Gauge
Door Pressure Gauge This Door Pressure Gauge, available from Evan Terry Associates, measures forces from 0-35 pounds on one side and 0-16 kilograms on the other....
-
Digital inclinometers (SmartTool®)
Digital inclinometers (SmartTool®), while slightly more expensive than standard levels, are easy to calibrate and use and can measure slopes in degrees, percent, and fractions per foot....
-
11B-407.2.1.1 Height
Call buttons and keypads shall be located within one of the reach ranges specified in Section 11B-308, measured to the centerline of the highest operable part. Exception: Reserved....
-
11B-407.2.1.1 Height
Call buttons and keypads shall be located within one of the reach ranges specified in Section 11B-308, measured to the centerline of the highest operable part. Exception: Reserved....
-
C. Technical standards for content validity studies
In the case of a selection procedure measuring a knowledge, skill, or ability, the knowledge, skill, or ability being measured should be operationally defined....
-
M303.2.4.2.2 Height
Wheelchair spaces shall include toe clearance 9 inches (230 mm) high minimum above the floor measured to a depth of 6 inches (150 mm) maximum measured from the toe end of the wheelchair...
-
Better Living AVIVA Soap Dispenser 1
off the wall for easy refilling Smooth, reliable Dispenser™ pump has a Lifetime Warranty Installs in minutes without tools, using waterproof silicone adhesive and 2-way tape...
-
3 [§ 4.3.7]
Unlike the running slope, which runs along the ramp, the cross slope is measured across the ramp....
-
§104.35(b)(3)
student with impaired sensory, manual, or speaking skills, the test results accurately reflect the student's aptitude or achievement level or whatever other factor the test purports to measure...
-
Performance for Surface Firmness and Stability
The baseline measurements affirmed the RP was operable and calibrated....
-
2. What are examples of auxiliary aids and services for students with hearing, vision, and speech disabilities?
signed or finger‐spelled communication into spoken words.26 For a person who is blind, deaf‐blind, or has low vision, some examples of auxiliary aids and services are qualified readers, taped...
-
GENERAL EFFECTIVE COMMUNICATION PROVISIONS
frames, for fulfilling requests from the public for sign language or oral interpreters, real-time transcription services, and documents in alternate formats (Braille, large print, cassette tapes...
-
Paragraph (b) (Advisory Guidance)
The most common strategy for achieving this requirement is the use of a standard 9 mm miniature plug-in jack, common to virtually every personal tape player or radio....
