this code shall apply to the construction, alteration, relocation, enlargement, replacement, repair, equipment, use and occupancy, location, maintenance, removal and demolition of every building...
Search Results "Fire-Building Surface"
Filters
Commonly Searched Documents
-
101.2 Scope
-
UNREASONABLE HARDSHIP
When the enforcing agency finds that compliance with the building standard would make the specific work of the project affected by the building standard infeasible, based on an overall evaluation...
-
Allegion Von Duprin 94/95 Series INPACT Recessed Exit Device
Specifications 94/95 INPACT Concealed Vertical Rod Devices Models: 9447 and 9547 Fire-Rated Models: 9447-F and 9547-F Device Handing: Non-handed Functions...
-
Preliminary Guidelines for SEWF Installation
Do not saturate surface with these lubricants. After compaction the thickness will be approximately 40 mm (1.6 in.). 3....
-
Receivers: ADA Standard Section 219.3
Section 219.3 covers scoping requirements in the current ADA Standards for receivers for assistive listening systems.
-
TTY Scoping [4.1.3(17)(c)]
TTY Scoping [4.1.3(17)(c)] ADAAG requires at least one TTY on site when there are four or more pay phones (and at least one is interior) and in specific buildings or locations when a...
-
3.5.1 General
If the main entrance to a building is not accessible, in the vicinity of the closest accessible entrance. Accessible means of egress out of a building....
-
11B-202.1 General
Additions and alterations to existing buildings or facilities shall comply with Section 11B-202. ...
-
ELEMENT
[DSA-AC] An architectural or mechanical component of a building, facility, space or site....
-
Addition
An expansion, extension, or increase in the gross floor area or height of a building or facility....
-
[A] REPAIR
The reconstruction or renewal of any part of an existing building for the purpose of its maintenance....
-
F202.2 Additions
Each addition to an existing building or facility shall comply with the requirements for new construction....
-
4.2 Q. What if new public and common use spaces are also being added?
If new public and common use areas or buildings are also added, they are required to be accessible....
-
202.1 General
Additions and alterations to existing buildings or facilities shall comply with 202....
-
Construction
Construction is building a new trail, recreation site, or facility where there was none before....
-
68.30(1) Federal Property
Buildings or facilities owned, operated, or leased by the federal government;...
-
11B-202.1 General
Additions and alterations to existing buildings or facilities shall comply with Section 11B-202....
-
11B-202.1 General
Additions and alterations to existing buildings or facilities shall comply with Section 11B-202....
-
11B-903.5 Height
The top of the bench seat surface shall be 17 inches (432 mm) minimum and 19 inches (483 mm) maximum above the finish floor or ground....
-
903.5 Height
The top of the bench seat surface shall be 17 inches (430 mm) minimum and 19 inches (485 mm) maximum above the finish floor or ground....
-
Check Height and Location of the Pushbutton
Check Height and Location of the Pushbutton Confirm that pushbutton height and location conform to specifications and can be reached by a person in a wheelchair, from a hard surfaced level...
-
903.5 Height
The top of the bench seat surface shall be 17 inches (430 mm) minimum and 19 inches (485 mm) maximum above the finish floor or ground....
-
Parking Spaces for Vehicles Other Than RVs [F244.2.3.2.2]
Parking spaces for vehicles other than RVs within camping units with mobility features must comply with the following technical requirements for width, surface, and slope....
-
R305.2.2 Parallel Curb Ramps
On parallel curb ramps, detectable warning surfaces shall be placed on the turning space at the flush transition between the street and sidewalk....
