where such a clearance would create an insurmountable gap on a mini-high platform or where the physical structure of an existing station does not allow such clearance), barriers must be used...
Search Results "US Census Bureau"
Filters
Commonly Searched Documents
-
§ 37.42(e)(2)
-
12201(c)(3)
Paragraphs (1), (2), and (3) shall not be used as a subterfuge to evade the purposes of subchapter I and III of this chapter....
-
§35.163(b)
The international symbol for accessibility shall be used at each accessible entrance of a facility....
-
[A] PUBLIC WAY
A street, alley or other parcel of land open to the outside air leading to a street, that has been deeded, dedicated or otherwise permanently appropriated to the public for public use and...
-
A4.10.12 Car Controls
Industry-wide standardization of elevator control panel design would make all elevators significantly more convenient for use by people with severe visual impairments....
-
508 Standards
The standards for ICT developed, procured, maintained, or used by agencies subject to Section 508 of the Rehabilitation Act as set forth in 508 Chapters 1 and 2 (36 CFR Part 1194, Appendix...
-
Outcome Summary
Keep it short using bullet points....
-
4.10.1 General
Freight elevators shall not be considered as meeting the requirements of this section unless the only elevators provided are used as combination passenger and freight elevators for the public...
-
Seat [4.21.3]
Folding seats can be used....
-
Graphic Conventions [3.1]
ADAAG uses rounded-off ("soft") metric conversions in most cases; more precise ("hard") conversions may be incorporated in future revisions of the guidelines....
-
Curbs [4.21.7]
This height limit also allows wheelchair footrests to clear the curb so that a person using a wheelchair can partially pull into the stall for transfer to the seat....
-
4.1.7(3)(a)
EXCEPTION: A ramp with a slope no greater than 1:6 for a run not to exceed 2 ft (610 mm) may be used as part of an accessible route to an entrance....
-
4.1.6(3)(h) Dressing Rooms
Where only unisex dressing rooms are provided, accessible unisex dressing rooms may be used to fulfill this requirement....
-
4.1.7(2)(a)
EXCEPTION: A ramp with a slope no greater than 1:6 for a run not to exceed 2 ft (610 mm) may be used as part of an accessible route at an entrance....
-
A4.6.3 PARKING SPACES
High-top vans, which disabled people or transportation services often use, require higher clearances in parking garages than automobiles....
-
Beach Access Route
A continuous, unobstructed path designed for pedestrian use that crosses the surface of a beach or that leads from a pedestrian access point to the high tide level at tidal beaches; mean...
-
§ 35.163(b)
The international symbol for accessibility shall be used at each accessible entrance of a facility....
-
§ 38.97(c)
or stanchions shall be provided in the entrance to the car in a configuration which allows passengers to grasp such assists from outside the car while starting to board, and to continue using...
-
§ 38.115(c)
or stanchions shall be provided in the entrance to the car in a configuration which allows passengers to grasp such assists from outside the car while starting to board, and to continue using...
-
§ 37.42(e)(2)
where such a clearance would create an insurmountable gap on a mini-high platform or where the physical structure of an existing station does not allow such clearance), barriers must be used...
-
11B-104.1 Dimensions
This section clarifies the dimensioning conventions used in this chapter. Dimensions stated as a "maximum" or "minimum" provide a dimensional range for design purposes. ...
-
11B-708.2 Audible and visual indicators
A light can be used to indicate visually that assistance is on the way. Signs indicating the meaning of visual signals should be provided....
-
§ 37.55 Intercity rail station accessibility
All intercity rail stations shall be made readily accessible to and usable by individuals with disabilities, including individuals who use wheelchairs, as soon as practicable, but in...
-
11B-104.1 Dimensions
This section clarifies the dimensioning conventions used in this chapter. Dimensions stated as a "maximum" or "minimum" provide a dimensional range for design purposes....