Both sections incorporate a disparate impact standard to ensure the effectiveness of the legislative mandate to end discrimination....
Search Results "End Transfer Surface"
Commonly Searched Documents
-
Section 36.204 Administrative Methods (Preamble, Section-by-Section Analysis)
-
Accessibility Engineering Specialists
The Board encourages any efforts to move accessibility design into the mainstream of telecommunications and will work cooperatively with any established group to further those ends....
-
3. MINIMUMS, MAXIMUMS AND SPECIFYING AT THE LIMIT
It will also more often produce an end result of strict and literal compliance with the stated requirements and eliminate enforcement difficulties and issues that might otherwise arise....
-
Wheelchair Accessible Gates
Web sites with designs that allow wheelchair access while restricting access by ATVs and motorcycles are listed near the end of this tech tip....
-
1. New Format for Guidelines
published in 2004, we submitted the guidelines, as amended by the final rule, to the Federal Register as a Word document without figures, except for four mandatory symbols included at the end...
-
3.1 Plan Ahead
., it’s on the same side of the street as the bus stop, the first entrance at the end of the block after you get off the bus)?...
-
After Completing the Survey
For more information about temporary modifications, see Temporary Solutions for Election Day at the end of each section of this document....
-
4.3.5 Turning clearance
In confined dead end spaces, a 360-degree turn should be used as the basis for the minimum space required since individuals often move around within small space without actually leaving...
-
4.16.6 Dispensers
Alternatively, Horty Elving and Associates used a toilet paper holder at the end of each swing-away grab bar (e.g., Figure 11) at Bridges Medical Services, Ada, MN (Horty, Elving & Associates...
-
705.1.2 Dome Spacing
Truncated domes in a detectable warning surface shall have a center-to-center spacing of 1.6 inches (41 mm) minimum and 2.4 inches (61 mm) maximum, and a base-to-base spacing of 0.65 inch...
-
Seat Height
Seat Height The lift must be designed so that the seat will make a stop between a minimum of 16 inches and maximum of 19 inches (measured from the deck to the top of the seat surface,...
-
11B-505.10.1 Top and bottom extension at ramps
Extensions shall return to a wall, guard, or the landing surface, or shall be continuous to the handrail of an adjacent ramp run....
-
4.7.2 SLOPE
Maximum slopes of adjoining gutters, road surface immediately adjacent to the curb ramp, or accessible route shall not exceed 1.20....
-
4.1.1 General
In alterations, where a condition for exception in section 1.1 prohibits full compliance with a specific requirement for clear floor or ground space surface slope, size, or location, the...
-
1131A.2 Changes greater than ½ inch
Changes in level greater than ½ inch (12.7 mm) shall be made by means of a sloped surface not greater than 1 unit vertical in 20 units horizontal (5-percent slope), or a ramp, elevator or...
-
13) Detectable warnings
Must be a textured surface on the door handle or hardware (§4.29)....
-
1131A.2 Changes greater than ½ inch
Changes in level greater than ½ inch (12.7 mm) shall be made by means of a sloped surface not greater than 1 unit vertical in 20 units horizontal (5-percent slope), or a ramp, elevator or...
-
11B-503.3.3 Marking
The area within the borderlines shall be marked with hatched lines a maximum of 36 inches (914 mm) on center in a color contrasting with that of the aisle surface....
- Delta Two Handle Widespread Lavatory Faucet- Less Grid Strainer 3549LF-WFLGHDF
- Just Manufacturing Brass Service Sink Faucet with Hose Thread
- ACS Communication Access Realtime Translation (CART) Services
- PEMKO 5 1/8" Thermal Barrier Threshold No. 252X3-FG
- PEMKO 8 1/8" Thermal Barrier Threshold No. 254X4-FG
- Georgia-Pacific enMotion® Recessed Automated Touchless Towel Dispenser