The transfer surface shall be 30 inches (760 mm) wide minimum and 15 inches (381mm) deep minimum. Advisory M301.2.2 Size. The size requirements in this section apply only to the...
Search Results "Braille Position"
Filters
Commonly Searched Documents
-
M301.2.2 Size
-
M301.2 Transfer Surface
A transfer surface shall be provided and shall comply with M301.2.
-
Accessibility Solutions and Research Center (AMAC) at Georgia Institute of Technology
AMAC Accessibility was incubated out of the University System of Georgia in 2005 to help post-secondary disability services offices provide complete, timely, efficient accommodations...
-
M302.3.2 Leg Supports (Section-by-Section Analysis)
The MDE NPRM did not propose to require stirrups to provide a method of supporting, positioning, and securing the patient’s legs for diagnostic equipment used by patients in the seated position...
-
Exit Doors: ADA Standard Section 216.4.1
Section 216.4.1 covers scoping requirements in the current ADA Standards for signs at exit doors.
-
11B-216.4.1 Exit doors
Signs required by Chapter 10, Section 1013.4 at doors to exit passageways, exit discharge, and exit stairways shall comply with Sections 11B-703.1, 11B-703.2, 11B-703.3, and...
-
M305.2.4.1 Circular Cross Section
Transfer supports with circular cross sections shall have an outside diameter of 1 ¼ inches (32 mm) minimum and 2 inches (51 mm) maximum.
-
M305.2.1.2 Side Transfer Supports
Transfer supports for transfer surfaces complying with M301.2.3.2 shall be capable of supporting transfer on each side of the transfer surface.
-
M305.2.1.1 End Transfer Supports
Transfer supports for transfer surfaces complying with M301.2.3.1 and M302.2 shall be located on the short side (length) opposite the transfer side.
-
Issue: Effective Communication
In addition, city governments often fail to provide materials in alternate formats (Braille, large print, or audio cassettes) to individuals who are blind or have low vision....
-
5.2.2.2 Transfer Surface Depth Recommendation for M302
5.2.2.2 Transfer Surface Depth Recommendation for M302 The Committee recommends a minimum depth requirement of 17 inches for equipment used by patients in seated positions....
-
5.2.2.1 Transfer Surface Width Recommendations for M302
Recommendations for M302 The Committee recommends 21 inches for the minimum width of the transfer surface of examination chairs and other equipment primarily used by patients in a seated position...
-
M301.3.2 Leg Supports
Where stirrups are provided, leg supports shall also be provided and shall comply with M305.4.
-
11B-407.2.3.1 Floor designation
Floor designations shall be provided in both raised characters and braille. Raised characters shall be 2 inches (51 mm) high....
-
11B-407.2.3.1 Floor designation
Floor designations shall be provided in both raised characters and Braille. Raised characters shall be 2 inches (51 mm) high....
-
11B-407.2.3.1 Floor designation
Floor designations shall be provided in both raised characters and braille. Raised characters shall be 2 inches (51 mm) high....
-
M305.2.4.2 Non-Circular Cross Section
Transfer supports with non-circular cross sections shall have a cross-section dimension of 2 inches (51 mm) maximum and a perimeter dimension of 4 inches (100 mm) minimum and 4.8...
-
5.3.1 Permitted Obstructions to Transfer Sides for M301 and M302
5.3.1 Permitted Obstructions to Transfer Sides for M301 and M302 Description: Transfer side provisions are the same for M301 and M302 and require the transfer surface to be...
-
1. Standing Supports
provider should position her in a seated position for safe imaging.”...
-
407.4.8.2.3 Frequency
The verbal annunciator shall have a frequency of 300 Hz minimum to 3000 Hz maximum.
-
407.4.8.1.2 Location
Indicators shall be located above the car control panel or above the door.
-
11B-407.4.8.1.2 Location
Indicators shall be located above the car control panel or above the door.
-
11B-407.4.8.2.3 Frequency
The verbal annunciator shall have a frequency of 300 Hz minimum to 3000 Hz maximum.
-
407.4.8.2.3 Frequency
The verbal annunciator shall have a frequency of 300 Hz minimum to 3000 Hz maximum.
