TABLE 11B-703.3.1 BRAILLE DIMENSIONS MEASUREMENT RANGE MINIMUM IN INCHES MAXIMUM IN INCHES Dot base diameter 0.059 (1.5 mm) to 0.063 (1.6 mm)...
Search Results "Feasibility (Technical, Infeasible, Structural, Maximum Extent)"
Filters
Commonly Searched Documents
-
11B-703.3.1 Dimensions and capitalization
-
11B-703.3.1 Dimensions and capitalization
TABLE 11B-703.3.1 BRAILLE DIMENSIONS MEASUREMENT RANGE MINIMUM IN INCHES MAXIMUM IN INCHES Dot base diameter...
-
Universaling Design
It is based on the premise that the design of products and environments ought to ‘be usable by all people, to the greatest extent possible, without the need for adaptation or specialized...
-
Spinal Cord Injury Association of Washington (SCIAW)
SCIAW promotes and encourages people with spinal cord injury to thrive in society to the fullest extent possible....
-
11B-201.1 Scope
The 1991 Standards and the 2010 Standards apply to fixed or built-in elements of buildings, structures, site improvements, and pedestrian routes or vehicular ways located on a site....
-
Amusement rides
The Department also notes that section 234.4.2 of the 2010 Standards only applies where the structural or operational characteristics of an amusement ride are altered....
-
Q3: Roadway Resurfacing Alteration Project and Curb Ramp Improvements
Public entities should not structure the scope of work to avoid ADA obligations to provide curb ramps when resurfacing a roadway. ...
-
1115B.4.5, Item 2
The structural strength of seats and their attachments shall comply with Section 1115B.7.2. Seats shall be mounted securely and shall not slip during use. ...
-
604.5 Grab Bars
sufficient to permit the installation of rear and side wall grab bars that fully meet all accessibility requirements including, but not limited to, required length, installation height, and structural...
-
2. DESIGN PROFESSIONAL IN GENERAL RESPONSIBLE CHARGE STATMENT
construction documents meets the requirements of the current applicable California Building Code (CBC) accessibility provisions for path of travel requirements for alterations, additions and structural...
-
Accessible Miniature Golf Courses
ADAAG addresses only the built environment (structures and grounds). The guidelines do not address operational issues....
-
R302.7 Surfaces
requirements in R302.7 apply to sidewalks and other pedestrian circulation paths, pedestrian street crossings and at-grade rail crossings, pedestrian overpasses and underpasses and similar structures...
-
Readily Achievable
employees; the number, type, and location of its facilities; and (5) If applicable, the type of operation or operations of any parent corporation or entity, including the composition, structure...
-
How to use this Manual
This manual is structured in the same sequence as the steps a passenger would encounter on a trip, i.e., requirements concerning planning a flight, the airport experience...
-
Amusement rides. (Section-by-Section Analysis)
The Department also notes that section 234.4.2 of the 2010 Standards only applies where the structural or operational characteristics of an amusement ride are altered....
-
Location
When accessible parking spaces are added in an existing parking lot or structure, locate the spaces on the most level ground close to the accessible entrance....
-
11B-201.1 Scope
The 1991 Standards and the 2010 Standards apply to fixed or built-in elements of buildings, structures, site improvements, and pedestrian routes or vehicular ways located on a site....
-
11B-407.2.1.4 Location
Responding cars are programmed for maximum efficiency by reducing the number of stops any passenger experiences....
-
1009.2.1 Pool Lift Location
Where multiple pool lift locations are provided, no more than one pool lift shall be required to be located in an area where the water level is 48 inches (1220 mm) maximum....
-
11B-1009.5.4 Transfer steps
Transfer step height shall be 8 inches (203 mm) maximum. The surface of the bottom tread shall extend to a water depth of 18 inches (457 mm) minimum below the stationary water level....
-
703.4.1 Height above Finish Floor or Ground
characters on signs shall be located 48 inches (1220 mm) minimum above the finish floor or ground surface, measured from the baseline of the lowest tactile character and 60 inches (1525 mm) maximum...
-
Section 4.26.2
Handrail gripping surfaces with a non-circular cross section must have a perimeter dimension of 4 inches to 6 ¼ inches, and a cross section dimension of 2 ¼ inches maximum....
-
M302.4.2 Clearance Around Base
The width of the base permitted within this clearance shall be 26 inches (660 mm) wide maximum at the edge of the examination surface and shall be permitted to increase at a rate of 1 inch...
-
M301.4.2 Clearance Around Base
The width of the base permitted within this clearance shall be 26 inches (660 mm) wide maximum at the edge of the examination surface and shall be permitted to increase at a rate of 1 inch...
