Clearance between handrail gripping surfaces and adjacent surfaces shall be 1½ inches (38 mm) minimum....
Search Results "Side Transfer Surface"
Filters
Commonly Searched Documents
-
11B-505.5 Clearance
-
11B-404.2.9 Door and gate opening force
Powered doors shall be controlled on both the interior and exterior sides of the doors by sensing devices, push plates, vertical actuation bars or other similar operating devices complying...
-
11B-404.2.9 Door and gate opening force
Powered doors shall be controlled on both the interior and exterior sides of the doors by sensing devices, push plates, vertical actuation bars or other similar operating devices complying...
-
11B-404.2.9 Door and gate opening force
Powered doors shall be controlled on both the interior and exterior sides of the doors by sensing devices, push plates, vertical actuation bars or other similar operating devices complying...
-
11B-608.5.3 Alternate roll-in type shower compartments
In alternate roll-in type shower compartments, the controls, faucets, and shower spray unit shall be located on the side wall of the compartment adjacent to the 16 inches (406 mm) minimum...
-
11B-705.1.1.4 Resiliency
Detectable warning surfaces shall differ from adjoining surfaces in resiliency or sound-on-cane contact....
-
Issue 5: Tactile arrow (in line)
Figure 13: APS installed on poles in the landscape strip, and still within reach from a level paved sidewalk surface....
-
Protruding Objects and Trails
Objects that extend into the travel way of a trail from the side or from overhead can be hazardous to people who are paying more attention to their companions than the travel route (figure...
-
Protruding Objects
Protruding Objects Common Problem: In areas inside and outside the lodging facility where people are expected to walk, objects protrude too far from the side, from posts, or hang down...
-
DORMA 8000 Series Exit Device
Economical and reliable exit device Rim, surface vertical rod, and surface vertical rod ''less bottom rod,'' along with a full range of trim options which allow access from the secure...
-
Check-out Aisle Counter Height
The counter surface of check-out aisle counters is required to be 38 inches high maximum. Comments from persons with disabilities considered 38 inches to be too high. Response....
-
Delimitations
following: Data from this study were obtained from a longitudinal study administered through the National Center on Accessibility (NCA) at Indiana University; One category of surface...
-
Recommendations for Further Action
are available for use on pedestrian trails and how various surface materials perform in different regions of the country....
-
M303.3.3.5 Handrails
Ramps with a rise greater than 6 inches (150 mm) shall provide handrails on both sides....
-
§ 1194.22(e)
(e) Redundant text links shall be provided for each active region of a server-side image map....
-
T602.3 Approach
One full unobstructed side of each wheelchair space shall adjoin or overlap a passenger access route....
-
d-ii
Are handrails installed on both sides of each ramp segment? [ADA Standards § 4.8.5] Yes No...
-
f-ii
Are handrails installed on both sides of each ramp segment? [ADA Standards § 4.8.5] Yes No...
-
Sec.36.308(a)(1)(i)
(i) Provide a reasonable number of wheelchair seating spaces and seats with removable aisle-side arm rests; and...
-
M303.3.3.5 Handrails
Ramps with a rise greater than 6 inches (150 mm) shall provide handrails on each side....
-
Tactile Symbols: ADA Standard Section 707.6.3.2
Function key surfaces shall have tactile symbols as follows: Enter or Proceed key: raised circle; Clear or Correct key: raised left arrow; Cancel key: raised letter ex; Add Value key: raised...
-
Dome Size: ADA Standard Section 705.1.1
Truncated domes in a detectable warning surface shall have a base diameter of 0.9 inch (23 mm) minimum and 1.4 inches (36 mm) maximum, a top diameter of 50 percent of the base diameter minimum...
-
11B-707.6.3.2 Tactile symbols
Function key surfaces shall have tactile symbols as follows: Enter or Proceed key: raised circle; Clear or Correct key: raised left arrow; Cancel key: raised letter ex; Add Value key: raised...
-
11B-411.2.1.5.1 Size
Buttons shall have square shoulders, be 3/4 inch (19.1 mm) minimum in the smallest dimension and shall be raised 1/8 inch (3.2 mm) plus or minus 1/32 inch (0.8 mm) above the surrounding surface...
