Ground surfaces located within use zones shall comply with ASTM F 1292 (1999 edition or 2004 edition)....
Search Results "Surface Smoothness"
Filters
Commonly Searched Documents
-
11B-1008.2.6.2 Use zones
-
Side-Hinged Door Ovens: ADA Standard Section 804.6.5.1
Side-hinged door ovens shall have the work surface required by 804.3 positioned adjacent to the latch side of the oven door....
-
R308.1.3.1 Surfaces
R308.1.3.1 Surfaces. The surfaces of boarding and alighting areas and boarding platforms shall comply with R302.7. Advisory R308.1.3.1 Surfaces....
-
11B-804.6.5.2 Bottom-hinged door ovens
Bottom-hinged door ovens shall have the work surface required by Section 11B-804.3 positioned adjacent to one side of the door....
-
11B-804.6.5.1 Side-hinged door ovens
Side-hinged door ovens shall have the work surface required by Section 11B-804.3 positioned adjacent to the latch side of the oven door....
-
505.8 Surfaces
505.8 Surfaces. Handrail gripping surfaces and any surfaces adjacent to them shall be free of sharp or abrasive elements and shall have rounded edges....
-
UltraPlay Recycled Rubber Tile Surface
Allows for individual tile replacement Superior shock absorption characteristics Provide a guaranteed critical fall height value Is a good solution for playgrounds erected on a smooth...
-
11B-504.4 Tread surface
Stair treads shall comply with Section 11B-302. Changes in level are not permitted. Exception: Treads shall be permitted to have a slope not steeper than 1:48.
-
11B-504.4 Tread surface
Stair treads shall comply with Section 11B-302. Changes in level are not permitted. Exception: Treads shall be permitted to have a slope not steeper than 1:48.
-
Is there a minimum distance between changes in level?
span vertical changes greater than ½”, must have level landings and clearances at the tops and bottoms of each run to provide adequate separation and resting intervals between sloping surfaces...
-
1.2.1 Walks and other non - ramp surfaces
1.2.1 Walks and other non - ramp surfaces. When overall running slope for walks is measured according to Section 1.1.3 a recommended tolerance for running slope is +1%....
-
T302 Walking Surfaces
[See subsections ...]
-
Surfaces (R302.7) (Section-by-Section Analysis)
Surfaces (R302.7) (Section-by-Section Analysis) The proposed technical requirements for surfaces apply to pedestrian access routes, including curb ramps and blended transitions, and accessible...
-
505.8 Surfaces
Handrail gripping surfaces and any surfaces adjacent to them shall be free of sharp or abrasive elements and shall have rounded edges....
-
505.8 Surfaces
Handrail gripping surfaces and any surfaces adjacent to them shall be free of sharp or abrasive elements and shall have rounded edges....
-
505.8 Surfaces
Handrail gripping surfaces and any surfaces adjacent to them shall be free of sharp or abrasive elements and shall have rounded edges....
-
M303.2.5 Surfaces
Wheelchair space surfaces shall not slope more than 1:48 in any direction....
-
M303.2.5 Surfaces
Wheelchair space surfaces shall not slope more than 1:48 in any direction....
-
Stabilizer Solutions StaLok Material Waterless Natural Pavement
Its unique surface characteristics resist weathering from water....
-
4.5.4 Gratings
If gratings are located in walking surfaces, then they shall have spaces no greater than 1/2 in (13 mm) wide in one direction (see Fig. 8(g))....
-
4.5.4 GRATINGS
If gratings are located in walking surfaces, then they shall have spaces no greater than 1/2 in (13 mm) wide in one direction (see Fig. 8(g))....
-
302.2 Carpet
Exposed edges of carpet shall be fastened to floor surfaces and shall have trim on the entire length of the exposed edge. Carpet edge trim shall comply with 303....
-
302.2 Carpet
Exposed edges of carpet shall be fastened to floor surfaces and shall have trim on the entire length of the exposed edge. Carpet edge trim shall comply with 303....
-
302.2 Carpet
Exposed edges of carpet shall be fastened to floor surfaces and shall have trim on the entire length of the exposed edge. Carpet edge trim shall comply with 303....
